This Bill of Materials is complete for the instructions that have been written. More parts WILL be needed as more instructions are added. I may have made mistakes, however. This page is automatically generated. Do not edit it. If you think you need to edit it, or have found a mistake, contact
RussNelson. The software which creates this listing is described at
PonokoBOMcode. This
BoM?? is best for locating parts needed for a particular assembly. For procuring parts, Zach's parts lister at
http://parts.reprap.org/ is best, but I have to figure out how to import this into it.
There are links to show changes at the bottom of the page. I've been changing the
BOM in the last several days; here is a link to the
BOM that existed before that:
http://reprap.org/bin/rdiff/Main/PonokoBOM?rev1=1.8&rev2=1.3 . Apparently the
BOM changed recently as well. That would be here:
http://reprap.org/bin/rdiff/Main/PonokoBOM?rev1=1.9&rev2=1.8 .
1 2200mm of 4.5mm ball chain
3 8mm i/d compression spring approximately 16mm long
12 M3 25mm screw
12 M3 nut
24 M3 washer
3 M8 60mm screw
6 M8 nut
9 M8 washer
24 4.5mm BBs ifthrust
3 608Z skate bearing ifskate
24 M3 25mm screw
24 M3 nut
48 M3 washer
6 M8 washer ifthrust
1 0.1uF capacitor
1 200-300mm of nichrome wire with a resistance of about 8 ohms
1 35mm piece of 10mm diameter PTFE rod with a 3mm hole drilled down the centre
1 40mm long piece of M6 brass bolt with a 3mm hole drilled right down the middle
2 608Z skate bearing
1 625ZZNSK bearing
5 M3 20mm screw
2 M3 30mm screw
4 M3 40mm screw
3 M3 50mm screw
11 M3 nut
23 M3 washer
2 M5 25mm screw
5 M5 30mm screw
4 M5 nut
1 M5 nyloc nut
4 M5 washer
1 M6 32mm o/d washer
2 M6 dome nut
2 M6 half- or press-nut
2 M6 washer
4 M8 nut
1 M8 studding 110mm
4 M8 washer
1 PTFE tape
1 PTFE thread sealing tape
1 gear motor
2 hole socket strip
4 large M3 washer
1 piece of hardened steel box-cutter blade
4 small, stout springs
1 thick, solid, insulated copper wire
4 M3 16mm screw
2 M3 25mm screw
6 M3 nut
8 M3 washer
8 M5 30mm screw
6 M5 nut
2 M5 nyloc nut
16 M5 washer
4 8mm diameter 500mm long bright steel rod
12 M3 40mm screw
12 M3 nut
24 M3 washer
4 M8 400mm studding
16 M8 nut
8 M8 washer
20 M3 25mm screw
20 M3 nut
40 M3 washer
8 M8 600mm studding
2 M8 650mm studding
40 M8 nut
40 M8 washer
6 M3 25mm screw
6 M3 nut
6 M3 washer
2 M5 16mm screw
2 M5 nut
2 1200mm 3.5mm (#6) ball chain
1 1200mm of 3.5mm ball chain
2 520mm bright steel rod ifNEMA23
4 8mm diameter 500mm long bright steel rod ifNEMA17
2 8mm diameter 500mm long bright steel rod ifNEMA23
3 M3 25mm screw
3 M3 nut
6 M3 washer
4 M5 50mm screw
2 M5 8mm grub screw
10 M5 nut
8 M5 washer
1 M8 half-nut
1 M8 nut
1 M8 washer
4 M3 12mm screw
4 M3 16mm screw
4 M3 20mm screw
16 M3 25mm screw ifNEMA17
2 M3 40mm screw
12 M3 nut
16 M3 nut ifNEMA17
22 M3 washer
32 M3 washer ifNEMA17
4 M5 25mm screw ifNEMA23
4 M5 nut ifNEMA23
8 M5 washer ifNEMA23
32 4.5mm BBs ifthrust
4 608Z skate bearing ifskate
32 M3 25mm screw
32 M3 nut
64 M3 washer
8 M8 washer ifthrust
17 M3 16mm screw
1 M3 20mm screw
19 M3 nut
22 M3 washer
1 608Z skate bearing
4 M3 12mm screw
4 M3 16mm screw
12 M3 20mm screw
8 M3 25mm screw
2 M3 40mm screw
24 M3 nut
46 M3 washer
1 M8 80mm studding
5 M8 nut
3 M8 washer
2 M8 wide aka fender washer
4 608Z skate bearing
8 M3 30mm screw
8 M3 nut
12 M3 washer
1 M8 500mm studding
2 M8 70mm bolt ifbolt
2 M8 70mm studding ifstudding
8 M8 nut
2 M8 nut ifstudding
2 M8 nyloc nut
12 M8 washer
4 80mm long 8mm diameter steel
8 M5 8mm grub screw
8 M5 nut
2 5mm i/d soft plastic tubing, approx 22mm long
4 M3 12mm screw
5 M3 25mm screw
10 M3 nut
14 M3 washer
2 M5 nut
2 M5 screw
4 M5 washer
8 8mm diameter 500mm long bright steel rod
8 M5 8mm grub screw
10 M5 grub screw
17 M5 nut
1 M8 half-nut
11 M8 nut
2 M8 washer
8 M3 25mm screw
3 M3 30mm screw
14 M3 nut
25 M3 washer
4 M5 25mm screw
1 M5 8mm grub screw
5 M5 nut
4 M5 washer
all
1 0.1uF capacitor
2 1200mm 3.5mm (#6) ball chain
1 1200mm of 3.5mm ball chain
1 200-300mm of nichrome wire with a resistance of about 8 ohms
1 2200mm of 4.5mm ball chain
1 35mm piece of 10mm diameter PTFE rod with a 3mm hole drilled down the centre
56 4.5mm BBs ifthrust
1 40mm long piece of M6 brass bolt with a 3mm hole drilled right down the middle
2 520mm bright steel rod ifNEMA23
2 5mm i/d soft plastic tubing, approx 22mm long
7 608Z skate bearing
7 608Z skate bearing ifskate
1 625ZZNSK bearing
4 80mm long 8mm diameter steel
12 8mm diameter 500mm long bright steel rod
4 8mm diameter 500mm long bright steel rod ifNEMA17
2 8mm diameter 500mm long bright steel rod ifNEMA23
3 8mm i/d compression spring approximately 16mm long
12 M3 12mm screw
29 M3 16mm screw
22 M3 20mm screw
120 M3 25mm screw
16 M3 25mm screw ifNEMA17
13 M3 30mm screw
20 M3 40mm screw
3 M3 50mm screw
213 M3 nut
16 M3 nut ifNEMA17
384 M3 washer
32 M3 washer ifNEMA17
2 M5 16mm screw
6 M5 25mm screw
4 M5 25mm screw ifNEMA23
13 M5 30mm screw
4 M5 50mm screw
19 M5 8mm grub screw
10 M5 grub screw
54 M5 nut
4 M5 nut ifNEMA23
3 M5 nyloc nut
2 M5 screw
36 M5 washer
8 M5 washer ifNEMA23
1 M6 32mm o/d washer
2 M6 dome nut
2 M6 half- or press-nut
2 M6 washer
4 M8 400mm studding
1 M8 500mm studding
8 M8 600mm studding
3 M8 60mm screw
2 M8 650mm studding
2 M8 70mm bolt ifbolt
2 M8 70mm studding ifstudding
1 M8 80mm studding
2 M8 half-nut
91 M8 nut
2 M8 nut ifstudding
2 M8 nyloc nut
1 M8 studding 110mm
79 M8 washer
14 M8 washer ifthrust
2 M8 wide aka fender washer
1 PTFE tape
1 PTFE thread sealing tape
1 gear motor
2 hole socket strip
4 large M3 washer
1 piece of hardened steel box-cutter blade
4 small, stout springs
1 thick, solid, insulated copper wire
--
RussNelson - 30 Jan 2009
to top