Search results
Create the page "Arduino pololu" on this wiki! See also the search results found.
- * 1 Electronics setup ([[Pololu Electronics]], [[Ramps]], [[Sanguinololu]], [[Generation 3 Electronics]], [ ...ou may find the [http://arduino.cc/ Arduino] [http://www.ladyada.net/learn/arduino/index.html Tutorials on Adafruit] quite useful.61 KB (6,470 words) - 12:27, 4 February 2015
- ...ga2560 Arduino Mega 2560] + [http://reprap.org/wiki/RAMPS_1.2 RAMPs v1.2] (Pololu A4983)1 KB (202 words) - 07:31, 28 December 2014
- |reprap = Arduino .../?p=548 Lincomatic's instructions] to install the CDC bootloader using the Pololu ISP I have used previously on ATmega644P and ATmega1284P micros. It's worth24 KB (3,846 words) - 11:04, 2 September 2019
- * The Pololu Stepper Drivers come with their male headers, so there's no need to purchas ! Pololu Header28 KB (4,400 words) - 13:13, 24 May 2016
- |description = RepRap Arduino Mega Pololu Shield Arduino MEGA based modular RepRap electronics.43 KB (2,222 words) - 08:46, 5 March 2019
- ...iki/RAMPS_1.4 RAMPS 1.4] + [http://arduino.cc/en/Main/ArduinoBoardMega2560 Arduino Mega 2560] | [[File:R Arduino mega 2560.jpg|100px]]26 KB (4,115 words) - 09:02, 1 December 2013
- * [http://arduino.cc/en/Main/ArduinoBoardMega2560 Arduino Mega 2560] ...iki/RAMPS_1.4 RAMPS 1.4] + [http://arduino.cc/en/Main/ArduinoBoardMega2560 Arduino Mega 2560]36 KB (5,799 words) - 13:05, 14 July 2014
- ...de construir una Prusa IT3. Ya he conseguido parte de la electrónica (el Arduino, la Ramps, la FA y un motor). La parte que me falta y la tornillería estoy ...de Obijuan en Youtube, y comence a investigar sobre el tema, me compre la arduino primero,y luego la RAMPS eso fue facil por que al no pesar mucho no hay tan198 KB (32,697 words) - 08:23, 30 November 2023
- Arduino MEGA based modular RepRap electronics. |reprap = Pololu Electronics5 KB (705 words) - 05:21, 21 May 2014
- ...igurar por hardware el micropaso. DEBEMOS PUENTEAR LOS TRES JUMPER DE CADA POLOLU. 2.- Durante las pruebas, una placa Arduino Mega, perdió el bootloader. Aún a día de hoy no he podido recargarlos (y1 KB (192 words) - 07:37, 26 February 2013
- |description = RepRap Arduino Mega Pololu Shield Arduino MEGA based modular RepRap electronics.29 KB (4,772 words) - 11:26, 17 January 2018
- ...sts of more than the control electronic. Also on it are 6 stepper drivers (Pololu compatible) and 4 opto endstops. '''Install''' Arduino Environment V0239 KB (1,415 words) - 09:14, 14 January 2018
- | [[RAMPS]] (Reprap Arduino Mega Pololu Shield) + Arduino Mega ...a que hay que comprarse el shield (lo que propiamente se llama RAMPS) y el Arduino Mega5 KB (873 words) - 20:53, 17 March 2014
- |description = Single board solution, Remix of Arduino mega and RAMPS |reprap = Pololu Electronics8 KB (1,253 words) - 05:06, 19 September 2016
- |description = RAMPS for Arduino Due = RAMPS For Arduino Due =5 KB (934 words) - 23:31, 20 March 2019
- ** Pololu y RAMPS v1.4, Soldado "Printer is now online" (22/08/12) ** Motores, RAMPS v1.4, Pololu Recibidos (17/08/12)3 KB (321 words) - 20:12, 16 July 2014
- It features an onboard ATmega2560. Its six motor outputs are powered by Pololu pin compatible stepper drivers. ** Arduino 2560-R3 compatible (works with [[Sprinter]], [[Repetier-Firmware]], [[Marli20 KB (2,993 words) - 03:04, 18 April 2022
- |description = A 5 axis RepRap ArduinoMega Pololu Shield This is a board that's very similar to other [[Pololu_Electronics|Pololu-based electronics]] implementations, including [[RAMPS]], but it can suppor10 KB (1,494 words) - 05:34, 6 July 2019
- |description = RepRap Arduino Mega Pololu Shield Arduino MEGA based modular RepRap electronics.24 KB (3,453 words) - 06:50, 16 November 2017
- * 4x driver-e Pololu pas cu pas, de schimb, de până la 1/16 microstepping. 09.02.2011: The master branch of FiveD on Arduino firmware is ported and seems to work but is not tested 100%. The config fil25 KB (3,883 words) - 03:30, 29 December 2014
