Videos

From RepRap
Revision as of 14:08, 20 July 2012 by Adrianbowyer (talk | contribs)
Jump to: navigation, search

Template:AboutHeader

Adrian and Ed's RepRap Introduction

<videoflash type="vimeo">5202148</videoflash>

RepRap Printing Blood Vessel Networks

<videoflash type="youtube">9VHFlwJQIkE</videoflash>

OhmEye's Introduction to 3D Printing and the Prusa Mendel

Whilst Adrian and Ed's video gives an excellent guide to the philosophy behind RepRap, the following video by OhmEye gives a more detailed guide for beginners on 3D printing with RepRap and the associated technicalities. <videoflash type="youtube">B3D56IpACME</videoflash>

Arduino & RepRap - Creating Wealth by Giving it Away

Adrian Bowyer and David Cuartilles' joint keynote talk at ICED11, Copenhagen". <videoflash type="youtube">2j84BDoNkt8</videoflash>


The RepRap Lab at Bath University

Adrian Bowyer gives a 10 minute tour of the lab where it all started. <videoflash type="youtube">FUB1WgiAFHg</videoflash>

Erik's RepRap Commercial

<videoflash type="youtube">cRH3RQ2F4Wk</videoflash>

Ericsson Multimedia Video on Adrian

<videoflash type="youtube">xvXHORiDHYM</videoflash>

The First Dutch Reprap Build-Party

<videoflash type="youtube">qq7roeoTM9g</videoflash>

Neil Underwood talks about RepRap and 3D printing at POSSCON 2011 in Columbia, SC.

<videoflash type="vimeo">21471714</videoflash>

BBC World Service item on RepRap in Arabic

<videoflash type="youtube">StC6BjWP1Dc</videoflash>

RepRap Instructional Videos

Throughout the documentation on this wiki there are a number of instructional videos. They are also gathered together here all in one place.

The video below is an introduction to the Mendel design:

<videoflash type="vimeo">6865848</videoflash>

Video on the key mechanical concepts behind Mendel's axes:

<videoflash type="vimeo">6982104</videoflash>

The following video shows the runs of all the wires in RepRap Mendel:

<videoflash type="vimeo">8397407</videoflash>

Videos on splitting the timing belts that drive Mendel's axes:

<videoflash type="vimeo">7027330</videoflash>

Video of Mendel's Y-axis working:

<videoflash type="blip">AYH27g8A</videoflash>

Video showing how to build on glass with a heated bed. This gives very good reliable results. It recommends that you clean the glass with nail varnish remover, which is fine. But check the ingredients list on the bottle. Some brands have a small quantity of lanolin or other oil dissolved in - they are useless as they leave a film of oil. Basically you want acetone, maybe a small amount of water, (plus - you'll usually find - a trace of bitrex, which stops people drinking the stuff).

<videoflash type="vimeo">17064268</videoflash>

Here's a video showing how to unload a print that has been made, and then set things up for a new one (including mildly amusing Adrian-confusion when the USB port lock has not been cleared). This is for a RepRap with an unheated bed:

<videoflash type="vimeo">11618621</videoflash>

This video shows how to maintain flatness in a RepRap be that is heated. The blue tape on the tray is Scotch painter's masking tape 2090, which can be obtained at most hardware shops:

<videoflash type="vimeo">14317374</videoflash>

This video shows how to tidy up parts post-reprapping:

<videoflash type="vimeo">14492980</videoflash>