3D printers on Kickstarter Hey everyone. I'm new to 3d printing. I've been modeling for a while and like the idea of being able to print out my own stuff. I've been researching and reading as much as I can. I'm good with my hands, tools and building things so a kit doesn't scare me. I've learned a bit but I'm sure I still have a ways to go. A printer has shown up on Kickstarter that caught my eye. It looks real pretty but unlike most of the other printers that I've seen. It's also pretty cheap compaired to all the other printers I've seen, $397! The Buccaneer The thing I don't like about it is that the software is cloud based. There is some grumbling in the comments section about it being a fake like Makibox. I was keeping an eye on Makibox but honestly I haven't checked his site in a while I was just wondering if someone with a little more experience could take a look at the page and tell me what they think. My first instinct is to stay away... This one looks a little more legit to me but I still feel a little unsure. The Kossel Pro https://reprap.org/forum/read.php?1,213772,213772#msg-213772 Wed, 11 Mar 2026 06:12:47 -0400 Phorum 5.2.23 https://reprap.org/forum/read.php?1,213772,215139#msg-215139 Re: 3D printers on Kickstarter https://reprap.org/forum/read.php?1,213772,215139#msg-215139
[www.makibox.com]]]> Nils Hitze General Tue, 04 Jun 2013 09:56:53 -0400 https://reprap.org/forum/read.php?1,213772,215138#msg-215138 Re: 3D printers on Kickstarter https://reprap.org/forum/read.php?1,213772,215138#msg-215138 > software is cloud based. There is some grumbling
> in the comments section about it being a fake like
> Makibox. I was keeping an eye on Makibox but
> honestly I haven't checked his site in a while

Why is everyone assuming that Makibox is a Fake?

Have a look at the latest 0.05 mm Prints and tell me that again.]]> Nils Hitze General Tue, 04 Jun 2013 09:56:13 -0400 https://reprap.org/forum/read.php?1,213772,214315#msg-214315 Re: 3D printers on Kickstarter https://reprap.org/forum/read.php?1,213772,214315#msg-214315 Jasper1984 General Sat, 01 Jun 2013 13:40:30 -0400 https://reprap.org/forum/read.php?1,213772,214229#msg-214229 Re: 3D printers on Kickstarter https://reprap.org/forum/read.php?1,213772,214229#msg-214229 if all it does is showing the general public that a 3D printer does not has to be as expensive as a cuby or fakerbot, than that is fine by me.

at least they can show something that already works.
something that can't be said of some other kickstarter projects.]]> possenier General Sat, 01 Jun 2013 06:25:51 -0400 https://reprap.org/forum/read.php?1,213772,214038#msg-214038 Re: 3D printers on Kickstarter https://reprap.org/forum/read.php?1,213772,214038#msg-214038
Kossel? Kind of expensive.. But good design cost good money.

It's beautiful to see all these new concepts.]]> Ohmarinus General Fri, 31 May 2013 12:39:18 -0400 https://reprap.org/forum/read.php?1,213772,214023#msg-214023 Re: 3D printers on Kickstarter https://reprap.org/forum/read.php?1,213772,214023#msg-214023 -------------------------------------------------------
> I have to say, the corexy is excellent for keeping
> that bar perpendicular, by increasing the tension
> on the belt you can correct the angle of the bar
> if it does happen to be off. also its rock solid,
> the trick however is getting the belts to cross
> over, and of course finding long enough belt.

I was looking at the CoreXY prototype last night and it finally dawned on me how they did it, I'd always assumed they just crossed the belts at an angle, but they don't, they run both belts at different heights which is much smarter.

>
> I tried the hbot at first but the thing would
> torque its way out of alignment with every move so
> its a no go unless your system has no give at all,
> which is pretty hard to come by.

Yes also my experience I think my last prototype was about as stiff as is practical using printed plastic parts and cheap LM8UU's and I still had issues.
The design is used in the dimension printers, but they use metal construction and I suspect they aren't using $2 bearings.]]> Polygonhell General Fri, 31 May 2013 12:03:20 -0400 https://reprap.org/forum/read.php?1,213772,214020#msg-214020 Re: 3D printers on Kickstarter https://reprap.org/forum/read.php?1,213772,214020#msg-214020 The XY stage they show uses 3 carriage and rail bearings, even sourcing from China in quantity those are about $40 a piece.
They are throwing in a raspberry Pi as part of their electronics solution.

So my assumption would be that they intend to make the money on the consumables.
Or they intend to change the design significantly.]]> Polygonhell General Fri, 31 May 2013 11:58:54 -0400 https://reprap.org/forum/read.php?1,213772,213836#msg-213836 Re: 3D printers on Kickstarter https://reprap.org/forum/read.php?1,213772,213836#msg-213836
I tried the hbot at first but the thing would torque its way out of alignment with every move so its a no go unless your system has no give at all, which is pretty hard to come by.]]> aduy General Fri, 31 May 2013 03:21:11 -0400 https://reprap.org/forum/read.php?1,213772,213818#msg-213818 Re: 3D printers on Kickstarter https://reprap.org/forum/read.php?1,213772,213818#msg-213818
Quote
alj_rprp
That being said the design seems to make sense and be real, but the dealbreaker for me is the cartridge system, just tailored to artificially inflate filament price and force you to use their own filament.

Their cartridge system doesn't force you to use their filament. You are free to fill the cartridges with your own filament, or ignore the cartridges altogether and just mount a spool above it.

They went with the cartridge system to keep with their design goal of being a sleek, all in one machine.]]> PomeroyB General Fri, 31 May 2013 02:43:25 -0400 https://reprap.org/forum/read.php?1,213772,213802#msg-213802 Re: 3D printers on Kickstarter https://reprap.org/forum/read.php?1,213772,213802#msg-213802 They announce stamped steel parts, there is no stamped part shown in the pic, and with what is pictured it does not even make sense to use stamped parts here, laser cuts will be cheaper and fine.

That being said the design seems to make sense and be real, but the dealbreaker for me is the cartridge system, just tailored to artificially inflate filament price and force you to use their own filament.]]> alj_rprp General Fri, 31 May 2013 01:23:52 -0400 https://reprap.org/forum/read.php?1,213772,213776#msg-213776 Re: 3D printers on Kickstarter https://reprap.org/forum/read.php?1,213772,213776#msg-213776
Here are a couple excellent reprap-based vendors to choose from (google for their websites):
Lulzbot
Makers Tool Works]]> crispy1 General Thu, 30 May 2013 21:55:22 -0400 https://reprap.org/forum/read.php?1,213772,213772#msg-213772 3D printers on Kickstarter https://reprap.org/forum/read.php?1,213772,213772#msg-213772
A printer has shown up on Kickstarter that caught my eye. It looks real pretty but unlike most of the other printers that I've seen. It's also pretty cheap compaired to all the other printers I've seen, $397!

The Buccaneer

The thing I don't like about it is that the software is cloud based. There is some grumbling in the comments section about it being a fake like Makibox. I was keeping an eye on Makibox but honestly I haven't checked his site in a while

I was just wondering if someone with a little more experience could take a look at the page and tell me what they think. My first instinct is to stay away...

This one looks a little more legit to me but I still feel a little unsure.

The Kossel Pro]]> Ardor General Thu, 30 May 2013 21:18:53 -0400