Ok, Its been a while since Ive messed with my firmware on my prusa printers. So I kinda remember how to set and calibrate those... But I have no clue where to begin in MARLIN to set it up for a delta.... Any tutorials out there? Id appreciate any help Thanks! Jeff https://reprap.org/forum/read.php?1,237121,237121#msg-237121 Fri, 06 Mar 2026 06:39:46 -0500 Phorum 5.2.23 https://reprap.org/forum/read.php?1,237121,237500#msg-237500 https://reprap.org/forum/read.php?1,237121,237500#msg-237500
Thanks for the link

Steve]]> Irish_Steve General Mon, 19 Aug 2013 04:49:28 -0400 https://reprap.org/forum/read.php?1,237121,237467#msg-237467 https://reprap.org/forum/read.php?1,237121,237467#msg-237467
[minow.blogspot.com]]]> swoozle General Sun, 18 Aug 2013 23:45:18 -0400 https://reprap.org/forum/read.php?1,237121,237462#msg-237462 https://reprap.org/forum/read.php?1,237121,237462#msg-237462 Does anyone have a version thats DEDICATED for a delta to help isolate the ACTUAL settings I need to adjust?
Thanks!
Jeff]]> Parabolic General Sun, 18 Aug 2013 23:19:18 -0400 https://reprap.org/forum/read.php?1,237121,237428#msg-237428 https://reprap.org/forum/read.php?1,237121,237428#msg-237428
Slightly off topic, I suspect I will be driving it from a laptop intially for calibration and testing, with the longer term plan being an Arduino Mega and Ramps 1.4 card, and an e3d hotend.

I will be using electronic limits rather than mechanical micro switches, and while I will need to work it out exactly "how" I'm going to do it, I suspect that a levelling sensor will also be needed to calibrate things for accuracy.

It would also be a huge help to get some feedback on what control and slicing programs people are using, and any issues they have with them, I've not yet made a definite decision which route to go, it seems that Marlin is the preferred firmware for the Pi, but beyond that, there's very little in depth information at the moment.

Thanks

Steve]]> Irish_Steve General Sun, 18 Aug 2013 19:57:08 -0400 https://reprap.org/forum/read.php?1,237121,237146#msg-237146 https://reprap.org/forum/read.php?1,237121,237146#msg-237146 I got that far, Im just hoping there was more documentation on it as there are plenty of deltas out there now.]]> Parabolic General Sat, 17 Aug 2013 19:20:03 -0400 https://reprap.org/forum/read.php?1,237121,237136#msg-237136 https://reprap.org/forum/read.php?1,237121,237136#msg-237136 Here [reprap.org], I found a link to the marlin firmware
Which is here, [github.com]
Have looked through the configuration.h file and see defines for delta, so I hope it does the job, there is
some calibration info on the Rostock page but I have not found much more than that
Good luck]]> Myles General Sat, 17 Aug 2013 18:31:49 -0400 https://reprap.org/forum/read.php?1,237121,237121#msg-237121 https://reprap.org/forum/read.php?1,237121,237121#msg-237121 Its been a while since Ive messed with my firmware on my prusa printers. So I kinda remember how to set and calibrate those... But I have no clue where to begin in MARLIN to set it up for a delta....
Any tutorials out there?
Id appreciate any help
Thanks!
Jeff]]> Parabolic General Sat, 17 Aug 2013 17:16:05 -0400