e3d v6 problem webt to use printer today after putting new filliment in and cant use as lcd reads 208 celsus max temp error even though the end is cold if i hold the thermister in the hole a little it reads 730 proterface cant heat cause of error any help https://reprap.org/forum/read.php?1,515856,515856#msg-515856 Wed, 15 Jul 2026 03:38:49 -0400 Phorum 5.2.23 https://reprap.org/forum/read.php?1,515856,517340#msg-517340 Re: e3d v6 problem https://reprap.org/forum/read.php?1,515856,517340#msg-517340 trist077 General Wed, 03 Jun 2015 15:55:39 -0400 https://reprap.org/forum/read.php?1,515856,517331#msg-517331 Re: e3d v6 problem https://reprap.org/forum/read.php?1,515856,517331#msg-517331
is there and otherthings in firmware that could be at error if i change the thermister numer the value on the lcd changes but when put back to 5 it becomes the same as before

could the board be at fault

i set slicer up to print at 240 to print and it extruder ok]]> trist077 General Wed, 03 Jun 2015 15:38:04 -0400 https://reprap.org/forum/read.php?1,515856,517321#msg-517321 Re: e3d v6 problem https://reprap.org/forum/read.php?1,515856,517321#msg-517321
Quote
trist077
rang today and there not there so got ring tommorow but the womon on the phone said you should not have any problems connecting it

Did you catch her name? Because she's wrong.]]> greenman100 General Wed, 03 Jun 2015 14:57:38 -0400 https://reprap.org/forum/read.php?1,515856,517320#msg-517320 Re: e3d v6 problem https://reprap.org/forum/read.php?1,515856,517320#msg-517320
Quote
javitopia
Although the pt100 is more precise and have a wider temperature margin in the e3d page it clearly states that they are only compatible with makerbot electronics and that they would require additional electronics to plug it in a ramps.

E3D's page states Ultimaker, not Makerbot. Makerbot uses a K-type thermocouple.]]> greenman100 General Wed, 03 Jun 2015 14:57:01 -0400 https://reprap.org/forum/read.php?1,515856,517309#msg-517309 Re: e3d v6 problem https://reprap.org/forum/read.php?1,515856,517309#msg-517309 asbo General Wed, 03 Jun 2015 14:22:59 -0400 https://reprap.org/forum/read.php?1,515856,517297#msg-517297 Re: e3d v6 problem https://reprap.org/forum/read.php?1,515856,517297#msg-517297 trist077 General Wed, 03 Jun 2015 14:02:35 -0400 https://reprap.org/forum/read.php?1,515856,517172#msg-517172 Re: e3d v6 problem https://reprap.org/forum/read.php?1,515856,517172#msg-517172 trist077 General Wed, 03 Jun 2015 09:40:18 -0400 https://reprap.org/forum/read.php?1,515856,517168#msg-517168 Re: e3d v6 problem https://reprap.org/forum/read.php?1,515856,517168#msg-517168
the only thing i tried its 05 for the thermistor in marlin i changed to 1 it wen t to 245 so put back to 5 as this is the resistor i have]]> trist077 General Wed, 03 Jun 2015 09:34:33 -0400 https://reprap.org/forum/read.php?1,515856,517038#msg-517038 Re: e3d v6 problem https://reprap.org/forum/read.php?1,515856,517038#msg-517038
As for the normal Thermistor, is not that hard to get it working. From what you tell it appears that you have ether a broken wire or the Thermistor leads are shorting. Make sure the fiberglass sleeving is pressed all the way down so when the termistor is bent and inserted into the hole, there are no copper exposed. Also press firmly the ferrules so the Thermistor leads and the cable make a good electrical connection and don't forget to insulate them (if the short then the readings will be way off). Take a look into the e3d assembly instructions, they are pretty clear and if you follow them precisely things should work as expect]]> javitopia General Wed, 03 Jun 2015 02:49:16 -0400 https://reprap.org/forum/read.php?1,515856,516807#msg-516807 Re: e3d v6 problem https://reprap.org/forum/read.php?1,515856,516807#msg-516807 trist077 General Tue, 02 Jun 2015 13:00:11 -0400 https://reprap.org/forum/read.php?1,515856,516768#msg-516768 Re: e3d v6 problem https://reprap.org/forum/read.php?1,515856,516768#msg-516768
Quote
trist077
ok so i need a amplifier board as my eletronics only support adc and the pt100 is rtd so where can i get such board

Have you asked the dumbass who sold the pt100 to you?]]> o_lampe General Tue, 02 Jun 2015 11:38:33 -0400 https://reprap.org/forum/read.php?1,515856,516691#msg-516691 Re: e3d v6 problem https://reprap.org/forum/read.php?1,515856,516691#msg-516691 trist077 General Tue, 02 Jun 2015 08:44:05 -0400 https://reprap.org/forum/read.php?1,515856,516502#msg-516502 Re: e3d v6 problem https://reprap.org/forum/read.php?1,515856,516502#msg-516502
Quote
trist077
bought from esd online and it said it would fit the v6 kit when bought with the new heatsink block

Right, but it doesn't output a thermistor style signal...]]> greenman100 General Mon, 01 Jun 2015 21:40:25 -0400 https://reprap.org/forum/read.php?1,515856,516364#msg-516364 Re: e3d v6 problem https://reprap.org/forum/read.php?1,515856,516364#msg-516364
Quote
trist077
bought from esd online and it said it would fit the v6 kit when bought with the new heatsink block

OK, it fit´s mechanically, but for the RAMPS you would need a interface-board.
-Olaf]]> o_lampe General Mon, 01 Jun 2015 14:56:08 -0400 https://reprap.org/forum/read.php?1,515856,516296#msg-516296 Re: e3d v6 problem https://reprap.org/forum/read.php?1,515856,516296#msg-516296 trist077 General Mon, 01 Jun 2015 13:12:32 -0400 https://reprap.org/forum/read.php?1,515856,516078#msg-516078 Re: e3d v6 problem https://reprap.org/forum/read.php?1,515856,516078#msg-516078
Quote
trist077
ordered the new pt100 from esd online a lot more accurate than a thermistor so hopefully this will sort it though

but now the thermister is unpluged from the board the displa is still showing 200 i unplugged the heatbed too that says 0 degrees

You know that a PT100 can't be connected to a thermistor connection, right? Two different kinds of signals.]]> greenman100 General Sun, 31 May 2015 23:49:38 -0400 https://reprap.org/forum/read.php?1,515856,516077#msg-516077 Re: e3d v6 problem https://reprap.org/forum/read.php?1,515856,516077#msg-516077
Quote
frankvdh
Quote
trist077
just looked on youtube and there should be a small bolt and washer holding thermistor in guess what mine never had one but i guess that what you get for buying secand hand

I have 2 Chinese hot ends, both claiming to be E3D V6. One has a small screw and PTFE washer to hold the thermistor in, the other doesn't. On the second one, the heater cartridge and thermistor wires are taped together, so that when the cartridge is in place, the thermistor is held in its hole.

I don't know which of these is the genuine E3D V6 design.

Neither.]]> greenman100 General Sun, 31 May 2015 23:48:49 -0400 https://reprap.org/forum/read.php?1,515856,516054#msg-516054 Re: e3d v6 problem https://reprap.org/forum/read.php?1,515856,516054#msg-516054
Quote
trist077
just looked on youtube and there should be a small bolt and washer holding thermistor in guess what mine never had one but i guess that what you get for buying secand hand

I have 2 Chinese hot ends, both claiming to be E3D V6. One has a small screw and PTFE washer to hold the thermistor in, the other doesn't. On the second one, the heater cartridge and thermistor wires are taped together, so that when the cartridge is in place, the thermistor is held in its hole.

I don't know which of these is the genuine E3D V6 design.]]> frankvdh General Sun, 31 May 2015 21:12:29 -0400 https://reprap.org/forum/read.php?1,515856,515941#msg-515941 Re: e3d v6 problem https://reprap.org/forum/read.php?1,515856,515941#msg-515941
but now the thermister is unpluged from the board the displa is still showing 200 i unplugged the heatbed too that says 0 degrees]]> trist077 General Sun, 31 May 2015 15:09:29 -0400 https://reprap.org/forum/read.php?1,515856,515911#msg-515911 Re: e3d v6 problem https://reprap.org/forum/read.php?1,515856,515911#msg-515911 -Olaf]]> o_lampe General Sun, 31 May 2015 13:33:48 -0400 https://reprap.org/forum/read.php?1,515856,515877#msg-515877 Re: e3d v6 problem https://reprap.org/forum/read.php?1,515856,515877#msg-515877
730 on the lcd
just looked on youtube and there should be a small bolt and washer holding thermistor in guess what mine never had one but i guess that what you get for buying secand hand
going to get a new thermistor and try]]> trist077 General Sun, 31 May 2015 11:22:14 -0400 https://reprap.org/forum/read.php?1,515856,515872#msg-515872 Re: e3d v6 problem https://reprap.org/forum/read.php?1,515856,515872#msg-515872 the_digital_dentist General Sun, 31 May 2015 11:12:00 -0400 https://reprap.org/forum/read.php?1,515856,515856#msg-515856 e3d v6 problem https://reprap.org/forum/read.php?1,515856,515856#msg-515856
proterface cant heat cause of error any help]]> trist077 General Sun, 31 May 2015 09:50:21 -0400