Hello Everyone, I have a prusa I3 printer. I am trying to print attached .stl file. (145.6 * 165 * 50 mm ) [attachment 64396 JBCover.docx] However when I printed perimeter then I found that the dimensions are off by 30 mm which is too high. I have used Slice3r slicer. Can someone help me to understand why this is happening. I am using SD card to store g code file. Regards, Radical Technology https://reprap.org/forum/read.php?1,572847,572847#msg-572847 Sun, 12 Jul 2026 02:48:55 -0400 Phorum 5.2.23 https://reprap.org/forum/read.php?1,572847,577025#msg-577025 https://reprap.org/forum/read.php?1,572847,577025#msg-577025
#define DEFAULT_AXIS_STEPS_PER_UNIT {80,80,400,634.42}
#define DEFAULT_MAX_FEEDRATE {500, 500, 2, 25}
#define DEFAULT_MAX_ACCELERATION {1800,1800,15,500}]]> 3DS-QUAD General Thu, 29 Oct 2015 10:12:46 -0400 https://reprap.org/forum/read.php?1,572847,576794#msg-576794 https://reprap.org/forum/read.php?1,572847,576794#msg-576794
Sadly everyday I am facing new problems.

1. I am using repetier V1.4 firmware and repetier host software. On hardware side, I am using Melzi V2.0 board, GT2 belt, 16 teeth pully for X and Y axis motors
2. For last 2 days, I am printing same part (refer image) and found that on first day it printed correctly till 90% and at 90% completion suddenly whole printing shifted in Y direction by around 5 mm and ruined my print.
3. On second day when I was printing same part layers shifted in Y direction at 70% completion. This shift was around 1 mm

Initially i thought it must be belt tension or Y axis pulley must be loose. But I checked everything and found it to be OK.
Also, layers dont continue to shift forever, i mean once they shift in Y direction at a certain point, they start printing further layers correctly on this new co ordinates instead of desired co ordinates.
Is it because I am printing from SD card.

Pls help. I desperately need to complete this part correctly. Its very frustrating to see the good print getting ruined due to shifting in Y direction.

Link to photograph: [attachment 64841 WP_20151029_002.jpg]]]> Radical Technology General Wed, 28 Oct 2015 22:54:52 -0400 https://reprap.org/forum/read.php?1,572847,574260#msg-574260 https://reprap.org/forum/read.php?1,572847,574260#msg-574260 elwood127 General Fri, 23 Oct 2015 00:22:15 -0400 https://reprap.org/forum/read.php?1,572847,574257#msg-574257 https://reprap.org/forum/read.php?1,572847,574257#msg-574257
I displaced X n Y axes using manual mode in repetier host. I gave command of 100mm n they travelled exactly 100 mm.
Even I checked steps/ mm values and found them correct when compared with Prusa calculator. Now I'm really confused why its printing less dimensions than actual design dimensions]]> Radical Technology General Thu, 22 Oct 2015 23:52:11 -0400 https://reprap.org/forum/read.php?1,572847,573399#msg-573399 https://reprap.org/forum/read.php?1,572847,573399#msg-573399 3DS-QUAD General Wed, 21 Oct 2015 05:30:45 -0400 https://reprap.org/forum/read.php?1,572847,573325#msg-573325 https://reprap.org/forum/read.php?1,572847,573325#msg-573325 * Maybe you are over-extruding: extruding too much filament make the nozzle scrape to the printed part.
* Maybe your bed is a bit too high
* Are your stepsticks calibrated? You must tune the stepsticks to adjust their power]]> kimented_ General Wed, 21 Oct 2015 02:15:18 -0400 https://reprap.org/forum/read.php?1,572847,573139#msg-573139 https://reprap.org/forum/read.php?1,572847,573139#msg-573139
But it seems I made some blunder in the wiring. Now my objects are shifting on Y axis after few layers. Please refer attached photo.
I have printed this part earlier with 0.1 mm layer height and it has come really smooth.

Can you guys help me why this is happening. Im sure this is not a mechanical issue. :(

Regards,

Radical]]> Radical Technology General Tue, 20 Oct 2015 13:23:38 -0400 https://reprap.org/forum/read.php?1,572847,572917#msg-572917 https://reprap.org/forum/read.php?1,572847,572917#msg-572917 Your STL file seems to be good: slic3r say that the part dimensions are 146.75x165x50mm. I think your error is due to a bad calibration of your printer. You can try this: use your host software to displace the X and Y axis of 100mm, and measure how much your printer move in reality. If it is not 100mm, you know that you should compute your steps per unit, and modify your firmware configuration with the right values.

[prusaprinters.org]]]> kimented_ General Tue, 20 Oct 2015 05:13:28 -0400 https://reprap.org/forum/read.php?1,572847,572847#msg-572847 https://reprap.org/forum/read.php?1,572847,572847#msg-572847
I have a prusa I3 printer. I am trying to print attached .stl file. (145.6 * 165 * 50 mm ) [attachment 64396 JBCover.docx]
However when I printed perimeter then I found that the dimensions are off by 30 mm which is too high.

I have used Slice3r slicer. Can someone help me to understand why this is happening. I am using SD card to store g code file.

Regards,

Radical Technology]]> Radical Technology General Tue, 20 Oct 2015 01:57:00 -0400