connecting analogue and digital ground? Hello people I still cannot get my extruder motor to turn as noted on this thread but have found some references to ensuring the analogue and digital ground be connected.... where are these pins? Noobman mentioned near the oscillator but I cannot identify them... I assume we are talking abut the extruder controller? please help.. Cheers https://reprap.org/forum/read.php?13,64849,64849#msg-64849 Thu, 16 Apr 2026 14:08:33 -0400 Phorum 5.2.23 https://reprap.org/forum/read.php?13,64849,64903#msg-64903 Re: connecting analogue and digital ground? https://reprap.org/forum/read.php?13,64849,64903#msg-64903
Mendel_Wiring_MB_Extruder.JPG

]]> rhmorrison Controllers Wed, 27 Oct 2010 06:58:04 -0400 https://reprap.org/forum/read.php?13,64849,64900#msg-64900 Re: connecting analogue and digital ground? https://reprap.org/forum/read.php?13,64849,64900#msg-64900
Also, the DIR and SPEED LEDs for both coils on the motot are on continuously... is this right?

The motor is certainly under tension - I can easily turn the shaft when the power is off but when the power is on and the whine is present it is pretty hard to turn the shaft.

Anyway - will try swapping the wires tonight and see what happens...

Just to confirm - the D9 and D10 pins are the ones right next to the respective labels? ie the left hand ones on their respective banks of 3 headers?

Also, how does one check to see whether a signal is getting sent? I have seen people mention oscilloscopes - is that what is used?]]> AgeingHippy Controllers Wed, 27 Oct 2010 06:48:33 -0400 https://reprap.org/forum/read.php?13,64849,64897#msg-64897 Re: connecting analogue and digital ground? https://reprap.org/forum/read.php?13,64849,64897#msg-64897
The symptoms of it missing are far worse than you report. I think the board fails to work at all unless the pot is set to one end and the temperature readings are screwed.

Your symptoms are normally the missing SCL, SDA links from the motherboard to the extruder, but as you say you have those I am at a loss to explain it.]]> nophead Controllers Wed, 27 Oct 2010 06:01:24 -0400 https://reprap.org/forum/read.php?13,64849,64894#msg-64894 Re: connecting analogue and digital ground? https://reprap.org/forum/read.php?13,64849,64894#msg-64894
I am afraid my German is not too hot and babelfish gives me a pretty dodgy translation....

If I looking at the board there are 2 blobs of solder to the right of the quadrature and to the left of the oscillator next to the C12 label and the other blob above it next to the 4.7K label.

On my Makerbot extruder board it looks just like this (although I do have a quadrature attached). Should I connect these 2 blobs?

Thanks

ps. Mr Gilmore - I will probably get another extruder board without that nasty whine later, but for now I want to move on :)]]> AgeingHippy Controllers Wed, 27 Oct 2010 04:54:06 -0400 https://reprap.org/forum/read.php?13,64849,64889#msg-64889 Re: connecting analogue and digital ground? https://reprap.org/forum/read.php?13,64849,64889#msg-64889 VDX Controllers Wed, 27 Oct 2010 03:43:02 -0400 https://reprap.org/forum/read.php?13,64849,64861#msg-64861 Re: connecting analogue and digital ground? https://reprap.org/forum/read.php?13,64849,64861#msg-64861 grrf.de]]]> nophead Controllers Tue, 26 Oct 2010 19:51:01 -0400 https://reprap.org/forum/read.php?13,64849,64856#msg-64856 Re: connecting analogue and digital ground? https://reprap.org/forum/read.php?13,64849,64856#msg-64856
Anyhow, there is on the atmel a agnd that is separate from dgrnd. (though the datasheet does specify that it cannot be more than Hrm.. Something.. from the dgnd) Do you have a link to the schematic for the extruder board that you're using? I'd expect that the schematic shows that they're already linked.

Suggestions:

Check the datasheet for your processor (atmel168 on the extruder board, I believe) This'll give you the pin numbers.
Check the silkscreen (white numbers printed on the board itself) The pins might be labeled or even broken out.
Check the schematic for the board (possibly they are already connected, probably have to refer to the datasheet to be sure of what all those pin numbers mean) This'll show if these pins are connected already, and give you a hint as to what they're connected to if not eachother, make it easier to do something about it.]]> jgilmore Controllers Tue, 26 Oct 2010 18:18:01 -0400 https://reprap.org/forum/read.php?13,64849,64849#msg-64849 connecting analogue and digital ground? https://reprap.org/forum/read.php?13,64849,64849#msg-64849
I still cannot get my extruder motor to turn as noted on this thread but have found some references to ensuring the analogue and digital ground be connected.... where are these pins? Noobman mentioned near the oscillator but I cannot identify them... I assume we are talking abut the extruder controller?

please help..

Cheers]]> AgeingHippy Controllers Tue, 26 Oct 2010 16:50:30 -0400