Do you recognise this board? Picture links: Front Back CPU Close Up There are no markings anywhere on the board front or back. It's the stock board in my MonoPrice MP10 Mini I'm wondering if it would be easy enough to replace with something better? 32 bit? Marlin/Duet? Any recommendations for something to replace this? Much thanks in advance for your suggestions! Jonty https://reprap.org/forum/read.php?13,858641,858641#msg-858641 Sun, 10 May 2026 10:48:35 -0400 Phorum 5.2.23 https://reprap.org/forum/read.php?13,858641,864865#msg-864865 Re: Do you recognise this board? https://reprap.org/forum/read.php?13,858641,864865#msg-864865 ghent360 Controllers Mon, 30 Dec 2019 02:16:08 -0500 https://reprap.org/forum/read.php?13,858641,858660#msg-858660 Re: Do you recognise this board? https://reprap.org/forum/read.php?13,858641,858660#msg-858660
It's a great little printer but it doesn't seem practical or viable to upgrade it.

I'd rather put the money and effort into a new printer with the exact specs that I want.

Thanks very much again!]]> Jonty Controllers Wed, 28 Aug 2019 21:29:21 -0400 https://reprap.org/forum/read.php?13,858641,858658#msg-858658 Re: Do you recognise this board? https://reprap.org/forum/read.php?13,858641,858658#msg-858658
First off the Touch LCD, 99% probably you cant re use that on anything else. Its unknown so no support for it...
And its uses non standard plugs for nearly everything, so expect to have to change all the plugs on all wires at the controller end.
No documentation of course so you going to have to trace out where all the wires go...

Then you need to look at the voltage of the current system, is it 12v is it 24v is it something else?

You need to identify all your major parts
Any fans? what voltage are they?
Whats the voltage and wattage of the hot end and heated bed?
What does it use to measure hot temperatures a thermocolouple or a thermistor, what are the specs?

Stepper motors are probably re usable if the main electronics are are 12v or 24v
But for everything else if you don't know their specification you need to replace them.]]> Dust Controllers Wed, 28 Aug 2019 20:21:06 -0400 https://reprap.org/forum/read.php?13,858641,858656#msg-858656 Re: Do you recognise this board? https://reprap.org/forum/read.php?13,858641,858656#msg-858656 Good point about the cap -
Any ideas about how I could upgrade to a decent board?]]> Jonty Controllers Wed, 28 Aug 2019 18:15:53 -0400 https://reprap.org/forum/read.php?13,858641,858651#msg-858651 Re: Do you recognise this board? https://reprap.org/forum/read.php?13,858641,858651#msg-858651 www.monoprice.com]

Images you can actually see



The only thing you can determine from your cpu picture is that it has 16 pins a side 56 total
and its a terrible design, strapping a heat sensitive cap to a heat generator??
]]> Dust Controllers Wed, 28 Aug 2019 17:02:01 -0400 https://reprap.org/forum/read.php?13,858641,858641#msg-858641 Do you recognise this board? https://reprap.org/forum/read.php?13,858641,858641#msg-858641
Front
Back
CPU Close Up

There are no markings anywhere on the board front or back.
It's the stock board in my MonoPrice MP10 Mini

I'm wondering if it would be easy enough to replace with something better? 32 bit? Marlin/Duet?
Any recommendations for something to replace this?

Much thanks in advance for your suggestions!

Jonty]]> Jonty Controllers Wed, 28 Aug 2019 12:44:35 -0400