MKS DLC 2.0 disconnected of TFT35 and not upgraded by USB I have two new Makerbase MKS DLC 2.0 cards, and both have the same problem: they do not connect with the TFT35 display and are not recognized by the USB port. Makerbase claims that the MKS DLC supports updating via USB (Windows 10) and I tried to update the firmware (GRBL) via XLoader but this application does not recognize the DLC: "Can't open port". The OpenBuilds application is also unable to connect to the DLC: "Port error: Opening COM9: File not found". The DLC has two LEDs, one red always on and one blue always flashing. I updated, via the SD card, the firmware for CNC and Laser on the TFT35, which seems to be working normally in both versions. Where am I going wrong? 2021-02-05-17-23-16.jpg mod_embed_images_loadimage('665dcb8a43ec0324284f246d4354ee2b', '/forum/thumbcache/01a/d07/74f/cce/479/15e/4e3/933/0e2/10e/61_800x400.jpg', 'https://i.postimg.cc/5jfFvptc/2021-02-05-17-23-16.jpg', 'https://reprap.org/forum/addon.php?13,module=embed_images,check_scaling=1,url=https%3A%2F%2Fi.postimg.cc%2F5jfFvptc%2F2021-02-05-17-23-16.jpg', '', 881248, 800, 400, 'Loading image ...', false); 2021-02-05-17-28-12.jpg mod_embed_images_loadimage('5381952d604287a81b4cef37a13f1b53', '/forum/thumbcache/54d/1d7/c5f/05d/602/55b/42d/eb5/0c3/e85/fe_800x400.jpg', 'https://i.postimg.cc/MfZMSZLZ/2021-02-05-17-28-12.jpg', 'https://reprap.org/forum/addon.php?13,module=embed_images,check_scaling=1,url=https%3A%2F%2Fi.postimg.cc%2FMfZMSZLZ%2F2021-02-05-17-28-12.jpg', '', 881248, 800, 400, 'Loading image ...', false); 2021-02-05-17-29-04.jpg mod_embed_images_loadimage('76f6071d54bba1533c73aa514fec4e56', '/forum/thumbcache/247/cfb/6e4/459/344/62c/61d/9d9/bce/8e1/81_800x400.jpg', 'https://i.postimg.cc/t7DnzP1s/2021-02-05-17-29-04.jpg', 'https://reprap.org/forum/addon.php?13,module=embed_images,check_scaling=1,url=https%3A%2F%2Fi.postimg.cc%2Ft7DnzP1s%2F2021-02-05-17-29-04.jpg', '', 881248, 800, 400, 'Loading image ...', false); https://reprap.org/forum/read.php?13,881248,881248#msg-881248 Sat, 06 Jun 2026 07:05:41 -0400 Phorum 5.2.23 https://reprap.org/forum/read.php?13,881248,881298#msg-881298 Re: MKS DLC 2.0 disconnected of TFT35 and not upgraded by USB https://reprap.org/forum/read.php?13,881248,881298#msg-881298
Drivers can be found here [sparks.gogo.co.nz]]]> Dust Controllers Sat, 06 Feb 2021 18:19:08 -0500 https://reprap.org/forum/read.php?13,881248,881280#msg-881280 Re: MKS DLC 2.0 disconnected of TFT35 and not upgraded by USB https://reprap.org/forum/read.php?13,881248,881280#msg-881280 I appreciate your suggestion.

It does not seem to need IP01 for MKS DLC, which has its own USB port.
It is basically an Arduino Uno although the Arduino IDE does not recognize the board either.

I think Windows is installing the wrong driver but I can't find an appropriate driver.


MKS DLC Features
- CPU is ATMEGA328P-AU, 8bit 20MHZ, 5V logic level, stronger anti-interference type...
- Support Laser and CNC...
- Dupport writing machine...
- Support MKS TFT24/32/35 connect by AUX-1, and TFT_CNC firmware support Laser mode and CNC mode...
- Support grbl firmware...
- Support update firmware by USB...
- Support upload firmware hex file by Xloader...


]]> asasergio Controllers Sat, 06 Feb 2021 09:37:11 -0500 https://reprap.org/forum/read.php?13,881248,881268#msg-881268 Re: MKS DLC 2.0 disconnected of TFT35 and not upgraded by USB https://reprap.org/forum/read.php?13,881248,881268#msg-881268
ie you need a [github.com] for this tool

uploading via usb would use avrdude or AVRDUDESS]]> Dust Controllers Fri, 05 Feb 2021 22:41:31 -0500 https://reprap.org/forum/read.php?13,881248,881248#msg-881248 MKS DLC 2.0 disconnected of TFT35 and not upgraded by USB https://reprap.org/forum/read.php?13,881248,881248#msg-881248
Makerbase claims that the MKS DLC supports updating via USB (Windows 10) and I tried to update the firmware (GRBL) via XLoader but this application does not recognize the DLC: "Can't open port". The OpenBuilds application is also unable to connect to the DLC: "Port error: Opening COM9: File not found".

The DLC has two LEDs, one red always on and one blue always flashing.

I updated, via the SD card, the firmware for CNC and Laser on the TFT35, which seems to be working normally in both versions.

Where am I going wrong?






]]> asasergio Controllers Fri, 05 Feb 2021 17:34:12 -0500