Please Help | MKS Gen L V2.0 Error Device Not Recognized I have MKS Gen L V2.0 and when used for the first time, I installed CH340G drivers and it worked fine but one day I was trying to install firmware and I inserted the SD card with Marlin on it. I tried to connect it to PronterFace and it got connected, showed me the Marlin version and everything, but then I reconfigured the firmware and it did not work so I pulled my USB cord out of my laptop and tried to reconnect, it did not work after that, shows the error, 'Device Not Recognized.' (Interestingly, I have a clone Arduino Mega2560 which uses CH340G drivers and that did not work as well after that. I used the clone as a metric to see if my drivers work.) Now I reinstalled Windows and CH340G drivers and the clone Mega2560 works fine (COM3) but the MKS Board shows the error, 'Device Not Recognized.' mod_embed_images_loadimage('1f6b05df3713014345ba48c3a0e60be0', 'https://reprap.org/forum/addon.php?13,module=embed_images,url=https%3A%2F%2Fibb.co%2FNK5vT0f', 'https://ibb.co/NK5vT0f', 'https://reprap.org/forum/addon.php?13,module=embed_images,check_scaling=1,url=https%3A%2F%2Fibb.co%2FNK5vT0f', '', 883696, 800, 400, 'Loading image ...', false); mod_embed_images_loadimage('2089bcf9ec9a6f18a58782ee531ed983', 'https://reprap.org/forum/addon.php?13,module=embed_images,url=https%3A%2F%2Fibb.co%2F5LFBjKj', 'https://ibb.co/5LFBjKj', 'https://reprap.org/forum/addon.php?13,module=embed_images,check_scaling=1,url=https%3A%2F%2Fibb.co%2F5LFBjKj', '', 883696, 800, 400, 'Loading image ...', false); (The four little LEDs on the MKS board light up fine, I tried inserting SD card with fresh build of Marlin as well.) Each little contribution will be greatly appreciated. Thank You so much:P https://reprap.org/forum/read.php?13,883696,883696#msg-883696 Mon, 08 Jun 2026 17:10:06 -0400 Phorum 5.2.23 https://reprap.org/forum/read.php?13,883696,883756#msg-883756 Re: Please Help | MKS Gen L V2.0 Error Device Not Recognized https://reprap.org/forum/read.php?13,883696,883756#msg-883756
bootloader is firmware

It will not help

It is either dead or your windows is very broken. (try it on other machines)]]> Dust Controllers Mon, 03 May 2021 04:17:04 -0400 https://reprap.org/forum/read.php?13,883696,883744#msg-883744 Re: Please Help | MKS Gen L V2.0 Error Device Not Recognized https://reprap.org/forum/read.php?13,883696,883744#msg-883744 ifleep Controllers Sun, 02 May 2021 12:58:23 -0400 https://reprap.org/forum/read.php?13,883696,883719#msg-883719 Re: Please Help | MKS Gen L V2.0 Error Device Not Recognized https://reprap.org/forum/read.php?13,883696,883719#msg-883719
I tried removing the hardware and I tried the same drivers from Chinese site. I had installed fresh copy of Windows but I'm sure I did nothing that could fry the board :(

Still it doesn't work.]]> ifleep Controllers Sat, 01 May 2021 10:55:25 -0400 https://reprap.org/forum/read.php?13,883696,883717#msg-883717 Re: Please Help | MKS Gen L V2.0 Error Device Not Recognized https://reprap.org/forum/read.php?13,883696,883717#msg-883717
nothing you can do in firmware will stop the computer seeing it. (it may not respond or do anything useful due to bad code, but windows will always see it)

It is either dead hardware or windows

Remove all unneeded hardware, ie all stepper drivers and lcd/tfts and re test it

also try these drivers. [learn.sparkfun.com]]]> Dust Controllers Sat, 01 May 2021 09:43:16 -0400 https://reprap.org/forum/read.php?13,883696,883696#msg-883696 Please Help | MKS Gen L V2.0 Error Device Not Recognized https://reprap.org/forum/read.php?13,883696,883696#msg-883696
I tried to connect it to PronterFace and it got connected, showed me the Marlin version and everything, but then I reconfigured the firmware and it did not work so I pulled my USB cord out of my laptop and tried to reconnect, it did not work after that, shows the error, 'Device Not Recognized.'
(Interestingly, I have a clone Arduino Mega2560 which uses CH340G drivers and that did not work as well after that. I used the clone as a metric to see if my drivers work.)

Now I reinstalled Windows and CH340G drivers and the clone Mega2560 works fine (COM3) but the MKS Board shows the error, 'Device Not Recognized.'




(The four little LEDs on the MKS board light up fine, I tried inserting SD card with fresh build of Marlin as well.)

Each little contribution will be greatly appreciated. Thank You so much:P
]]> ifleep Controllers Fri, 30 Apr 2021 11:00:18 -0400