X, Y, and Z axis. Error: printer halted. kill (Make noise) Hello, a few days ago I had assembled 3d printer. After installing Marlin firmware, I had opened pronterface and tried to move X,Y or Z axis but it make noise and doesn't move. I had not install heated bed yet but hotend is working fine. When I click X,Y or Z homing it gives an [ERROR] Error:Printer halted. kill() called!. All the endstop is opened but not triggered. Copy of the firmware is also attached. I hope my problem get resolved. https://reprap.org/forum/read.php?14,842428,842428#msg-842428 Fri, 09 Oct 2026 18:48:39 -0400 Phorum 5.2.23 https://reprap.org/forum/read.php?14,842428,844082#msg-844082 Re: X, Y, and Z axis. Error: printer halted. kill (Make noise) https://reprap.org/forum/read.php?14,842428,844082#msg-844082 Abdul Mannan Mechanics Wed, 09 Jan 2019 13:12:06 -0500 https://reprap.org/forum/read.php?14,842428,842622#msg-842622 Re: X, Y, and Z axis. Error: printer halted. kill (Make noise) https://reprap.org/forum/read.php?14,842428,842622#msg-842622 This is a software protection feature to prevent cold extrusion, that could cause damage to your 3D Printer.

However you can disable this with M302 S0 ; always allow extrusion (disable checking)]]> Roberts_Clif Mechanics Fri, 28 Dec 2018 08:08:19 -0500 https://reprap.org/forum/read.php?14,842428,842579#msg-842579 Re: X, Y, and Z axis. Error: printer halted. kill (Make noise) https://reprap.org/forum/read.php?14,842428,842579#msg-842579 Abdul Mannan Mechanics Fri, 28 Dec 2018 01:16:33 -0500 https://reprap.org/forum/read.php?14,842428,842473#msg-842473 Re: X, Y, and Z axis. Error: printer halted. kill (Make noise) https://reprap.org/forum/read.php?14,842428,842473#msg-842473 Roberts_Clif Mechanics Thu, 27 Dec 2018 08:35:18 -0500 https://reprap.org/forum/read.php?14,842428,842434#msg-842434 Re: X, Y, and Z axis. Error: printer halted. kill (Make noise) https://reprap.org/forum/read.php?14,842428,842434#msg-842434 Abdul Mannan Mechanics Wed, 26 Dec 2018 21:38:37 -0500 https://reprap.org/forum/read.php?14,842428,842433#msg-842433 Re: X, Y, and Z axis. Error: printer halted. kill (Make noise) https://reprap.org/forum/read.php?14,842428,842433#msg-842433 #define X_DRIVER_TYPE A4988
#define Y_DRIVER_TYPE A4988
#define Z_DRIVER_TYPE A4988
//#define X2_DRIVER_TYPE A4988
//#define Y2_DRIVER_TYPE A4988
//#define Z2_DRIVER_TYPE A4988
#define E0_DRIVER_TYPE A4988
//#define E1_DRIVER_TYPE A4988
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988

When using
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
Include line below as you are not deploying a Probe.
#define FIX_MOUNTED_PROBE

You have almost the same setting that are use in my 3DP11/12 what 3D Printer is this for.]]> Roberts_Clif Mechanics Wed, 26 Dec 2018 21:01:15 -0500 https://reprap.org/forum/read.php?14,842428,842428#msg-842428 X, Y, and Z axis. Error: printer halted. kill (Make noise) https://reprap.org/forum/read.php?14,842428,842428#msg-842428 Abdul Mannan Mechanics Wed, 26 Dec 2018 17:17:04 -0500