Another Prusa I3 !! white & red HI, A few pictures of my prusa I3, new to 3D printing.. Electronics Ramps 1.4 complete DIY kit. yup!! had to solder all even the SMD components first time. Slight modification by adding a base to the printer also the X&Y idler I used small bearing from some old stepper motors.. In the past I've built lots of crazy stuffs in and around the house. But so far these is the one I am most impressed with. Many Many thanks to the community and every one for sharing. (I did face many difficulties, but dint have to post it, cause someone already did and got answers..:) I just read !!!Thanks ...Thanks... Thanks :) Along the line I short circuit the heat bed thermistor damaging my T1 which is Arduino mega pin A14, I rewired/insulated the thermistor moved it to T2 Arduino mega pin A15 edited the pins.h in sprinter all worked fine did a few prints. After taking down and rerouting my cables the T2 looks like it is damaged also!!, with high temperature readings with thermistor connected or not, how can i fix this? For now all I have is PLA plastics, shall I move to blue tape? :( and forget the heatbed?. CNC_PRUSA_BOX_FRAME4.jpg mod_embed_images_loadimage('06892bf6713d7533269fbc2279da38fc', '/forum/thumbcache/5a3/000/efd/548/973/03d/efd/b1b/a61/c1a/a8_800x400.png', 'https://lh4.googleusercontent.com/-jzpqMtaIbIw/UfEJ7d9yv0I/AAAAAAAADws/gdM8y_UaWE0/w1358-h757-no/CNC_PRUSA_BOX_FRAME4.jpg', 'https://reprap.org/forum/addon.php?151,module=embed_images,check_scaling=1,url=https%3A%2F%2Flh4.googleusercontent.com%2F-jzpqMtaIbIw%2FUfEJ7d9yv0I%2FAAAAAAAADws%2FgdM8y_UaWE0%2Fw1358-h757-no%2FCNC_PRUSA_BOX_FRAME4.jpg', '', 229820, 800, 400, 'Loading image ...', false); [lh6.googleusercontent.com] [lh6.googleusercontent.com] [lh5.googleusercontent.com] [lh5.googleusercontent.com] [lh3.googleusercontent.com] [lh5.googleusercontent.com] [lh3.googleusercontent.com] [lh3.googleusercontent.com] [lh5.googleusercontent.com] [lh6.googleusercontent.com] Here is a video of it printing Good luck!! https://reprap.org/forum/read.php?151,229820,229820#msg-229820 Sat, 13 Jun 2026 15:00:11 -0400 Phorum 5.2.23 https://reprap.org/forum/read.php?151,229820,231693#msg-231693 Re: Another Prusa I3 !! white & red https://reprap.org/forum/read.php?151,229820,231693#msg-231693 I wanted something strong and steady, plus I had enough hardwood lying around. as mention by hcker it is also cheaper :(.]]> Topicawox General Mendel Topics Thu, 01 Aug 2013 05:13:22 -0400 https://reprap.org/forum/read.php?151,229820,230141#msg-230141 Re: Another Prusa I3 !! white & red https://reprap.org/forum/read.php?151,229820,230141#msg-230141 hcker2000 General Mendel Topics Fri, 26 Jul 2013 13:19:30 -0400 https://reprap.org/forum/read.php?151,229820,230078#msg-230078 Re: Another Prusa I3 !! white & red https://reprap.org/forum/read.php?151,229820,230078#msg-230078
Out of curiosity, any reason for deciding to go with the box frame over the LC frame on the i3, or was it just design/looks preference?]]> RickM General Mendel Topics Fri, 26 Jul 2013 06:55:41 -0400 https://reprap.org/forum/read.php?151,229820,229820#msg-229820 Another Prusa I3 !! white & red https://reprap.org/forum/read.php?151,229820,229820#msg-229820 A few pictures of my prusa I3, new to 3D printing..
Electronics Ramps 1.4 complete DIY kit. yup!! had to solder all even the SMD components first time.
Slight modification by adding a base to the printer also the X&Y idler I used small bearing from some old stepper motors..
In the past I've built lots of crazy stuffs in and around the house. But so far these is the one I am most impressed with.

Many Many thanks to the community and every one for sharing. (I did face many difficulties, but dint have to post it, cause someone already did and got answers..:) I just read !!!Thanks ...Thanks... Thanks :)

Along the line I short circuit the heat bed thermistor damaging my T1 which is Arduino mega pin A14, I rewired/insulated the thermistor moved it to T2 Arduino mega pin A15 edited the pins.h in sprinter all worked fine did a few prints. After taking down and rerouting my cables the T2 looks like it is damaged also!!, with high temperature readings with thermistor connected or not, how can i fix this?

For now all I have is PLA plastics, shall I move to blue tape? :( and forget the heatbed?.




[lh6.googleusercontent.com]


[lh6.googleusercontent.com]

[lh5.googleusercontent.com]

[lh5.googleusercontent.com]

[lh3.googleusercontent.com]

[lh5.googleusercontent.com]

[lh3.googleusercontent.com]

[lh3.googleusercontent.com]

[lh5.googleusercontent.com]

[lh6.googleusercontent.com]


Here is a video of it printing

Good luck!!
]]> Topicawox General Mendel Topics Thu, 25 Jul 2013 08:25:38 -0400