Hello to all I just finished assembling my Prusa I3 and I am having quality problems when I print circles. As you can see, in the image attached, I have small gaps (see the arrows in the image) and until now I could not solve this problem. I think is the spacing between perimeter and infill but I do not know how to solve this problem. What could be causing this problem? I've followed these tutorials and apparently it's all right. [forum.seemecnc.com] and [reprap.org]% 27s_Calibration_Guide # E_Steps_Fine_Tuning I am using Marlin firmware, Ramps and Repetier host. Thank you https://reprap.org/forum/read.php?151,291478,291478#msg-291478 Sun, 06 Sep 2026 07:28:52 -0400 Phorum 5.2.23 https://reprap.org/forum/read.php?151,291478,293036#msg-293036 https://reprap.org/forum/read.php?151,291478,293036#msg-293036
Problem solved, I tested the Kisslicer and Cura, in both slicers the problem did not show up, now I'll see if I can put those parameters in the slic3r. ( I like very much Slic3r )

An interesting thing, Cura printed twice faster than the Slicer and no problem at all, no gaps, no lines everythinh ok.

Thank you to all for the tips and suggestions. Now let´s go print :)]]> Joberr General Mendel Topics Sat, 11 Jan 2014 11:26:52 -0500 https://reprap.org/forum/read.php?151,291478,292760#msg-292760 https://reprap.org/forum/read.php?151,291478,292760#msg-292760 Had the same problem with my Prusa i3, circles was ellipses.

In my case, it was mechanics, the belt attachment under the bed was loose. I remember I was able to move the bed (slightly but surely), when firmly holding the belt.

Check this out!

Christian]]> clefranc General Mendel Topics Fri, 10 Jan 2014 20:00:35 -0500 https://reprap.org/forum/read.php?151,291478,292501#msg-292501 https://reprap.org/forum/read.php?151,291478,292501#msg-292501
@Jefhei uncle bob told me the same thing, I downloaded Kisslicer and Cura, I'm trying to find a good tutorial for these programs and I will test them on Saturday.

@Kenzu I had a felling that could be something mechanical like that or the axes orthogonality, but after measuring the axes right angles they were fine. The backlash I think it is not so easy to measure it. I even thought about it and did not do those measures.
Do you think if I increase the "multiplier" in slic3r I could eliminate the underextrude?
I'll try anyway.

Thank you.]]> Joberr General Mendel Topics Fri, 10 Jan 2014 12:29:04 -0500 https://reprap.org/forum/read.php?151,291478,292233#msg-292233 https://reprap.org/forum/read.php?151,291478,292233#msg-292233
Edit: Maybe you also underextrude just a bit. You can see that when theres small gaps in your top layer.]]> Kenzu General Mendel Topics Fri, 10 Jan 2014 03:20:45 -0500 https://reprap.org/forum/read.php?151,291478,292097#msg-292097 https://reprap.org/forum/read.php?151,291478,292097#msg-292097 jefhei General Mendel Topics Thu, 09 Jan 2014 17:53:19 -0500 https://reprap.org/forum/read.php?151,291478,291937#msg-291937 https://reprap.org/forum/read.php?151,291478,291937#msg-291937
So far I only used the slic3r. I'll try another slicer to see what happens.

Yes, I am running a heated bed (MK2) and 3mm glass on it at 90C but I tried even at 110C and I have the same result.

I am using a 3mm filament. (Wade's Geared Extruder) Nozzle 0.4, retraction 1mm

For the hot end I tried temperatures between 220C to 235C with no significant variation, I have always the same "gaps".

Very slow.

Perimeter 20mm/s
infill 50mm/s
Solid infill 40mm/s
Top solid 30mm/s
First layer 30%


yes I am printing a skirt

Loop 2
Distance 6mm
Skirt heigh 1
minimum extrusion lenght 0

Thank you for your help]]> Joberr General Mendel Topics Thu, 09 Jan 2014 12:18:46 -0500 https://reprap.org/forum/read.php?151,291478,291544#msg-291544 https://reprap.org/forum/read.php?151,291478,291544#msg-291544
Are you running a heated bed? If so, how hot?

What kind of filament are you running?

How hot are you running your hot end?

How fast are you printing?

Are you printing a skirt? If not, I'd try it.]]> uncle_bob General Mendel Topics Wed, 08 Jan 2014 18:10:43 -0500 https://reprap.org/forum/read.php?151,291478,291478#msg-291478 https://reprap.org/forum/read.php?151,291478,291478#msg-291478
I just finished assembling my Prusa I3 and I am having quality problems when I print circles.

As you can see, in the image attached, I have small gaps (see the arrows in the image) and until now I could not solve this problem.
I think is the spacing between perimeter and infill but I do not know how to solve this problem.

What could be causing this problem?

I've followed these tutorials and apparently it's all right.

[forum.seemecnc.com] and

[reprap.org]% 27s_Calibration_Guide # E_Steps_Fine_Tuning

I am using Marlin firmware, Ramps and Repetier host.

Thank you]]> Joberr General Mendel Topics Wed, 08 Jan 2014 16:13:46 -0500