Dear all. I am looking for some help here :D been printing a few stls without a problem, and from today all the files do not load correctly. ( strangely only the ones that had never been loaded before) When i click Load, the layer count happens without any problem. the different thing arrives during the next steps, when the coil count is limited to 5, and the rest of the steps do not occur and it generates an additional export.gcode file. This file when i try to load it has a huge number of layers and it is inprintable. reface layer count 34 of 35... Preface layer count 35 of 35... Preface procedure took 0 seconds. Coil layer count 1 of 5... Coil layer count 2 of 5... Coil layer count 3 of 5... Coil layer count 4 of 5... Coil layer count 5 of 5... Coil procedure took 1 second. Flow procedure took 0 seconds. Feed procedure took 0 seconds. Limit procedure took 0 seconds. Alteration procedure took 0 seconds. The exported file is saved as /home/joan/Desktop/cage/New/Charrio pleint_export.gcode It took 2 seconds to export the file. thanks for the help I attach a file as an example. Best regards https://reprap.org/forum/read.php?154,186986,186986#msg-186986 Thu, 14 May 2026 18:42:20 -0400 Phorum 5.2.23 https://reprap.org/forum/read.php?154,186986,242272#msg-242272 https://reprap.org/forum/read.php?154,186986,242272#msg-242272
You two STL files are very very little to be printed… and there at the middle of the bed, don't know how Slic3r manages that, perhaps you only get layers upper than bed…]]> François Delègue Skeinforge Tue, 03 Sep 2013 05:01:20 -0400 https://reprap.org/forum/read.php?154,186986,242154#msg-242154 https://reprap.org/forum/read.php?154,186986,242154#msg-242154
If anyone has a suggestion, please let me know. Files Attached
[attachment 18468 mark_6_magnet_stand_highrepairedrepaired.stl]
[attachment 18469 mark_6_magnet_stand.stl]
[attachment 18470 mark_6_magnet_stand.ipt]
Thanks!]]> Polymerase Skeinforge Mon, 02 Sep 2013 16:40:21 -0400 https://reprap.org/forum/read.php?154,186986,186989#msg-186989 https://reprap.org/forum/read.php?154,186986,186989#msg-186989 The issue was the following, al the files were in a folter inside of another folder.
By putting the files on the descktop witgh only one level was sorted, stupid but true...]]> galkur Skeinforge Sat, 23 Feb 2013 03:56:57 -0500 https://reprap.org/forum/read.php?154,186986,186986#msg-186986 https://reprap.org/forum/read.php?154,186986,186986#msg-186986 I am looking for some help here :D
been printing a few stls without a problem, and from today all the files do not load correctly.
( strangely only the ones that had never been loaded before)

When i click Load, the layer count happens without any problem. the different thing arrives during the next steps, when the coil count is limited to 5, and the rest of the steps do not occur and it generates an additional export.gcode file.

This file when i try to load it has a huge number of layers and it is inprintable.



reface layer count 34 of 35...
Preface layer count 35 of 35...
Preface procedure took 0 seconds.
Coil layer count 1 of 5...
Coil layer count 2 of 5...
Coil layer count 3 of 5...
Coil layer count 4 of 5...
Coil layer count 5 of 5...
Coil procedure took 1 second.
Flow procedure took 0 seconds.
Feed procedure took 0 seconds.
Limit procedure took 0 seconds.
Alteration procedure took 0 seconds.
The exported file is saved as /home/joan/Desktop/cage/New/Charrio pleint_export.gcode
It took 2 seconds to export the file.


thanks for the help
I attach a file as an example.

Best regards]]> galkur Skeinforge Sat, 23 Feb 2013 03:48:43 -0500