Stepper motor wont turn One of my stepper motors for a 3D printer just vibrates and doesn't turn, it used to though. [www.banggood.com] I have tried swapping the connection, changing the step stick but doesn't work. I have also taken it out of the printer. Any help appreciated. https://reprap.org/forum/read.php?160,533050,533050#msg-533050 Sun, 19 Jul 2026 00:17:06 -0400 Phorum 5.2.23 https://reprap.org/forum/read.php?160,533050,594755#msg-594755 Re: Stepper motor wont turn https://reprap.org/forum/read.php?160,533050,594755#msg-594755
If one motor works you could try the other motors in that slot to see if the motor isn't working or if it is something else.]]> bonze77 Stepper Motors, Servo Motors, DC Motors Wed, 09 Dec 2015 11:33:09 -0500 https://reprap.org/forum/read.php?160,533050,594648#msg-594648 Re: Stepper motor wont turn https://reprap.org/forum/read.php?160,533050,594648#msg-594648
Quote
bonze77
Solved :X

It was a firmware problem -_-

// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
#define X_ENABLE_ON 0
#define Y_ENABLE_ON 0
#define Z_ENABLE_ON 0
#define E_ENABLE_ON 0 // For all extruders

hey, are you sure about this ? because, my marlin have same code which you written here, but still motor doesn't move !! :( help]]> yogesh.dp Stepper Motors, Servo Motors, DC Motors Wed, 09 Dec 2015 05:15:25 -0500 https://reprap.org/forum/read.php?160,533050,534028#msg-534028 Re: Stepper motor wont turn https://reprap.org/forum/read.php?160,533050,534028#msg-534028
It was a firmware problem -_-

// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
#define X_ENABLE_ON 0
#define Y_ENABLE_ON 0
#define Z_ENABLE_ON 0
#define E_ENABLE_ON 0 // For all extruders]]> bonze77 Stepper Motors, Servo Motors, DC Motors Sat, 18 Jul 2015 13:35:25 -0400 https://reprap.org/forum/read.php?160,533050,533698#msg-533698 Re: Stepper motor wont turn https://reprap.org/forum/read.php?160,533050,533698#msg-533698
Also I have changed the arduino.]]> bonze77 Stepper Motors, Servo Motors, DC Motors Fri, 17 Jul 2015 11:19:33 -0400 https://reprap.org/forum/read.php?160,533050,533058#msg-533058 Re: Stepper motor wont turn https://reprap.org/forum/read.php?160,533050,533058#msg-533058 dc42 Stepper Motors, Servo Motors, DC Motors Wed, 15 Jul 2015 19:17:17 -0400 https://reprap.org/forum/read.php?160,533050,533050#msg-533050 Stepper motor wont turn https://reprap.org/forum/read.php?160,533050,533050#msg-533050
[www.banggood.com]

I have tried swapping the connection, changing the step stick but doesn't work.
I have also taken it out of the printer.

Any help appreciated.]]> bonze77 Stepper Motors, Servo Motors, DC Motors Wed, 15 Jul 2015 18:59:55 -0400