Megatronics V2.0+Sainsmart 12864 LCD&repetier FW ,LCD does not display text i have Megatronics V2.0+Sainsmart 12864 LCD&repetier FW ,LCD does not display text,WHY? Megatronics V2.0+Sainsmart 12864 LCD&repetier FW ,LCD does not display text QQ%E5%9B%BE%E7%89%8720140801134020.jpg mod_embed_images_loadimage('9cb8f5e5c8bc0c923024e5bbc4dc31f2', '/forum/thumbcache/d15/2f3/834/f6c/91b/857/e1c/71c/586/e1b/d3_800x400.png', 'https://lh4.googleusercontent.com/-E6F_QSu9w-U/U9spa9PYCHI/AAAAAAAAALE/1uBUmBwx5AY/w424-h565-no/QQ%E5%9B%BE%E7%89%8720140801134020.jpg', 'https://reprap.org/forum/addon.php?178,module=embed_images,check_scaling=1,url=https%3A%2F%2Flh4.googleusercontent.com%2F-E6F_QSu9w-U%2FU9spa9PYCHI%2FAAAAAAAAALE%2F1uBUmBwx5AY%2Fw424-h565-no%2FQQ%25E5%259B%25BE%25E7%2589%258720140801134020.jpg', '', 389864, 800, 400, 'Loading image ...', false); QQ%E5%9B%BE%E7%89%8720140801134029.jpg mod_embed_images_loadimage('b3fe4fdce631a4288bb56e86d45b43cf', '/forum/thumbcache/19a/da5/e66/bbc/c5f/d3a/0f7/6ce/65e/3a0/2d_800x400.png', 'https://lh4.googleusercontent.com/-CxF4IgZWkgc/U9speo1tcUI/AAAAAAAAALU/mJnlo048sCY/w424-h565-no/QQ%E5%9B%BE%E7%89%8720140801134029.jpg', 'https://reprap.org/forum/addon.php?178,module=embed_images,check_scaling=1,url=https%3A%2F%2Flh4.googleusercontent.com%2F-CxF4IgZWkgc%2FU9speo1tcUI%2FAAAAAAAAALU%2FmJnlo048sCY%2Fw424-h565-no%2FQQ%25E5%259B%25BE%25E7%2589%258720140801134029.jpg', '', 389864, 800, 400, 'Loading image ...', false); https://reprap.org/forum/read.php?178,389864,389864#msg-389864 Mon, 18 May 2026 05:56:12 -0400 Phorum 5.2.23 https://reprap.org/forum/read.php?178,389864,393151#msg-393151 Re: Megatronics V2.0+Sainsmart 12864 LCD&repetier FW ,LCD does not display text https://reprap.org/forum/read.php?178,389864,393151#msg-393151 ruigrx Delta Machines Sun, 10 Aug 2014 06:37:31 -0400 https://reprap.org/forum/read.php?178,389864,390257#msg-390257 Re: Megatronics V2.0+Sainsmart 12864 LCD&repetier FW ,LCD does not display text https://reprap.org/forum/read.php?178,389864,390257#msg-390257 AndyCart Delta Machines Sat, 02 Aug 2014 01:52:37 -0400 https://reprap.org/forum/read.php?178,389864,390208#msg-390208 Re: Megatronics V2.0+Sainsmart 12864 LCD&repetier FW ,LCD does not display text https://reprap.org/forum/read.php?178,389864,390208#msg-390208
After my spherical magnet came unglued and nearly caused a minor catastrophe the other day, I think that my next project will either be getting a tri-axis accelerometer onto the effector plate as a Z-min probe and safety monitor, or else borrowing a page from Formula 1 and adding suspension tethers in case of another rod separation. Maybe a piece of long shock cord between the effector and top frame to hang the effector in mid-air if the rods let go?????]]> vreihen Delta Machines Fri, 01 Aug 2014 19:59:52 -0400 https://reprap.org/forum/read.php?178,389864,389991#msg-389991 Re: Megatronics V2.0+Sainsmart 12864 LCD&repetier FW ,LCD does not display text https://reprap.org/forum/read.php?178,389864,389991#msg-389991
Check out my Cherry Pi thread. I finally cracked the springs and strings delta rods!

Andy]]> AndyCart Delta Machines Fri, 01 Aug 2014 08:01:21 -0400 https://reprap.org/forum/read.php?178,389864,389973#msg-389973 Re: Megatronics V2.0+Sainsmart 12864 LCD&repetier FW ,LCD does not display text https://reprap.org/forum/read.php?178,389864,389973#msg-389973
Attached is my Repetier 0.91 rev 5 or 6 (not 7). It is set up for a Delta printer and will auto-home when started, so disconnect your stepper motors before booting it up if you load it as-is into your own Megatronics 2.0 board. It should work with rev7, but I just have not upgraded to test it yet.

It has been a few months since I set this up, but I think that all of my changes for the LCD-12864 were in ui.h . You will also need to get the u8glib and install it into your Arduino libraries following online directions if you have not done so already. I marked comments with "AE3 was here" for most changes, so you can follow what was changed. I also made a few tweaks to the other UI files, but those were for cosmetic purposes. (I wanted the printer name and company name to be above the Repetier version string on the bootup LCD splash screen, and I may have set the boot screen to stay on for 10 seconds instead of 2 seconds in a moment of vanity.)

Hope this helps to get your board and LCD up and running.....]]> vreihen Delta Machines Fri, 01 Aug 2014 06:52:54 -0400 https://reprap.org/forum/read.php?178,389864,389864#msg-389864 Megatronics V2.0+Sainsmart 12864 LCD&repetier FW ,LCD does not display text https://reprap.org/forum/read.php?178,389864,389864#msg-389864 Megatronics V2.0+Sainsmart 12864 LCD&repetier FW ,LCD does not display text


]]> ruigrx Delta Machines Fri, 01 Aug 2014 02:03:38 -0400