Hello, I'm new to this forum and this is my first post but I relay need some advice for bed tilt in my custom delta. I have a smoothieware and calibrated with the 626pilot firmware (but also with the stock firmware) and while the probe tell me that I have quite perfect bed: [BH] Determining the probe-from height. [PR] Priming probe 1 times. [BH] Bed height set to 352.919 [PR] Priming probe 1 times. [DM] Depth to bed surface at center: 751 steps (0.000 mm) [PD] -0.019 [PD] [PD] [ 0.000] -0.031 -0.006 -0.006 [ 0.000] [PD] [PD] -0.006 -0.006 0.000 -0.013 -0.013 [PD] [PD] [ 0.000] -0.025 0.000 -0.006 [ 0.000] [PD] [PD] -0.006 [PD] Best=0.000, worst=0.031, min=-0.031, max=0.000, mu=-0.005, sigma=0.008, energy=0.011 I can't understand why ther is a huge gap from the z axis to the x. The first layer height is set to 0.3mm. I tried to register manually the endstop after I need to rearrange the radius without find a solution! The autocalibration routine seems to found a solution but at the end the prints are like the attached one. It' s about two weeks that I'm trying to understand the first cause of the problem but I really can't understand. So please I hope that someone can guide me in such way to find the possible problem or (at this point) to destroy all! Thank you. https://reprap.org/forum/read.php?178,518966,518966#msg-518966 Tue, 08 Sep 2026 21:18:04 -0400 Phorum 5.2.23 https://reprap.org/forum/read.php?178,518966,519511#msg-519511 https://reprap.org/forum/read.php?178,518966,519511#msg-519511 Now I aranged to reduce the gap to 0.2mm and the problem it's still there but only a realy small portion respect before and also 626pilot has released a new version of his fork of smothieware with a matrix of 7x7 point that has helped also to reduce that problem.
So for the moment thankyou to all.]]> franco888999 Delta Machines Tue, 09 Jun 2015 16:29:39 -0400 https://reprap.org/forum/read.php?178,518966,519082#msg-519082 https://reprap.org/forum/read.php?178,518966,519082#msg-519082 SergioMC Delta Machines Mon, 08 Jun 2015 15:39:10 -0400 https://reprap.org/forum/read.php?178,518966,518966#msg-518966 https://reprap.org/forum/read.php?178,518966,518966#msg-518966
I'm new to this forum and this is my first post but I relay need some advice for bed tilt in my custom delta.

I have a smoothieware and calibrated with the 626pilot firmware (but also with the stock firmware) and while the probe tell me that I have quite perfect bed:

[BH] Determining the probe-from height.
[PR] Priming probe 1 times.
[BH] Bed height set to 352.919
[PR] Priming probe 1 times.
[DM] Depth to bed surface at center: 751 steps (0.000 mm)
[PD] -0.019
[PD]
[PD] [ 0.000] -0.031 -0.006 -0.006 [ 0.000]
[PD]
[PD] -0.006 -0.006 0.000 -0.013 -0.013
[PD]
[PD] [ 0.000] -0.025 0.000 -0.006 [ 0.000]
[PD]
[PD] -0.006
[PD] Best=0.000, worst=0.031, min=-0.031, max=0.000, mu=-0.005, sigma=0.008, energy=0.011

I can't understand why ther is a huge gap from the z axis to the x.
The first layer height is set to 0.3mm.

I tried to register manually the endstop after I need to rearrange the radius without find a solution!
The autocalibration routine seems to found a solution but at the end the prints are like the attached one.

It' s about two weeks that I'm trying to understand the first cause of the problem but I really can't understand.
So please I hope that someone can guide me in such way to find the possible problem or (at this point) to destroy all!

Thank you.]]> franco888999 Delta Machines Mon, 08 Jun 2015 10:10:21 -0400