Delta pulley and idler dimensions question I am planning to replace MXL with GT2 on Delta and I would need some advice by answering the following questions: 1) The sizes of pulley and idler don't have to be the same as long as the driving side of the loop is in a vertical line top-down right? [attachment 67209 screenshot.482.png] 2) I plan to use 16 tooth pulleys that are about 13-14mm OD. If I were to look for 16tooth idlers I can't seem to find a bearing-based solution with toothed idler included. What do you guys use for idlers and how does the idler rotate on its shaft? Aluminum idler rotating on screw or even smooth shaft is going to wear off. What do you use for shaft? 3) I've seen many bearings as idlers solutions that don't flip the belts along the way so that the smooth side rides the bearings. What would you suggest regarding: a) bearings as idlers (have to be flanged? 2 non-flanged bearings side by side?) b) is it better to let the teeth of the belt ride the bearing or flip it along the length of the tower so the smooth side of the belt ride the bearing? Thanks. https://reprap.org/forum/read.php?178,593682,593682#msg-593682 Thu, 18 Jun 2026 10:24:59 -0400 Phorum 5.2.23 https://reprap.org/forum/read.php?178,593682,600354#msg-600354 Re: Delta pulley and idler dimensions question https://reprap.org/forum/read.php?178,593682,600354#msg-600354
Quote
DjDemonD
I'm thinking about going over to 16 tooth drive pulleys and these idler pulleys [pages.ebay.com] that should improve resolution and provide reliable idlers. The 3mm bearing will wear on the 3mm bolt but at an acceptable rate.

The resolution gain is minimal I don't know how much you would be gaining if you aim for that. I went to 20tooth pinion and 2 flanged bearings that have a difference of 0.4mm in diameter difference when the belt rides on them with the teeth on the bearing; if I reverse the belt then the diameter of the pinion+belt should be about the same with the idler+belt.

Quote
DjDemonD
Why not use quite large idler pulleys to reduce their rate of rotation, this should reduce noise/vibration and bearing wear?

Please check the sketch I have attached in my first post. I subscribe to the larger idler idea and would have used it from the beginning should I have designed my own printer. You only have to make sure the driving side of the belt is perfectly vertical so you would have to offset the idler center to one side somehow.]]> realthor Delta Machines Thu, 24 Dec 2015 04:17:32 -0500 https://reprap.org/forum/read.php?178,593682,600347#msg-600347 Re: Delta pulley and idler dimensions question https://reprap.org/forum/read.php?178,593682,600347#msg-600347 dc42 Delta Machines Thu, 24 Dec 2015 04:01:55 -0500 https://reprap.org/forum/read.php?178,593682,600340#msg-600340 Re: Delta pulley and idler dimensions question https://reprap.org/forum/read.php?178,593682,600340#msg-600340 pages.ebay.com] that should improve resolution and provide reliable idlers. The 3mm bearing will wear on the 3mm bolt but at an acceptable rate.

Why not use quite large idler pulleys to reduce their rate of rotation, this should reduce noise/vibration and bearing wear?]]> DjDemonD Delta Machines Thu, 24 Dec 2015 03:50:39 -0500 https://reprap.org/forum/read.php?178,593682,597383#msg-597383 Re: Delta pulley and idler dimensions question https://reprap.org/forum/read.php?178,593682,597383#msg-597383
Quote
realthor
Edit1: If I were to print a belt clamp with the two reversed negative shapes for the belt, I am afraid that will be quite long and I would still reduce the Z max. But I'll have to measure that on the real distance between the idler and the top carriage position.

Edit2: I just realized that timing belts can clamp on themselves to lock, so that might be the ticket to be able to achieve the third diagram without modifying the existing carriage. The clamp shouldn't be higher than the existing teeth lock on the carriage, which run for about 8 teeth worth of length, which, at 2mm pitch would be around 16mm. I have measured the existing embedded clamp and it has 22.6mm, while the distance from the end of the carriage to the pulley is about 30mm. This looks definitely feasible.
]]> realthor Delta Machines Wed, 16 Dec 2015 05:22:33 -0500 https://reprap.org/forum/read.php?178,593682,597380#msg-597380 Re: Delta pulley and idler dimensions question https://reprap.org/forum/read.php?178,593682,597380#msg-597380
Quote
realthor
Quote
dc42
I don't know if there is a way to securely stitch/clamp/bolt two sections of belt so I can cut 20mm of belt, reverse it and clamp/stitch/whatever to the other length of belt. This solution might be too stretched to work an i might opt for the spectra-belt combo instead.

I assume that 20mm section will never have to run over a pulley, so that it can be rigid. I suggest you lock the teeth of the two sections together, then hold them together in one of several ways:

- epoxy them in that position;

- clamp them between two small metal plates;

- print a plastic part with a slot in it, and push the belts into that slot - as on the Ormerod X-carriage.
]]> dc42 Delta Machines Wed, 16 Dec 2015 05:18:11 -0500 https://reprap.org/forum/read.php?178,593682,597378#msg-597378 Re: Delta pulley and idler dimensions question https://reprap.org/forum/read.php?178,593682,597378#msg-597378
Quote
dc42
If you have a half twist over a length of the belt that varies as in your second diagram, then the belt tension will vary with that length, and hence with carriage position. So the arrangement in the third diagram is better. This also lets you lock the teeth of the belt together in the carriage, which avoids the tension in the belt putting stress on the printed carriage parts. RepRapPro does this in the X carriage of their Ormerod printer.

I agree with you. However, in my situation, the carriage is injection molded so I can't really see a way to adopt the third diagram, which involves re-printing the carriage. I don't know if there is a way to securely stitch/clamp/bolt two sections of belt so I can cut 20mm of belt, reverse it and clamp/stitch/whatever to the other length of belt. This solution might be too stretched to work an i might opt for the spectra-belt combo instead.]]> realthor Delta Machines Wed, 16 Dec 2015 05:09:33 -0500 https://reprap.org/forum/read.php?178,593682,597373#msg-597373 Re: Delta pulley and idler dimensions question https://reprap.org/forum/read.php?178,593682,597373#msg-597373 dc42 Delta Machines Wed, 16 Dec 2015 04:42:40 -0500 https://reprap.org/forum/read.php?178,593682,597370#msg-597370 Re: Delta pulley and idler dimensions question https://reprap.org/forum/read.php?178,593682,597370#msg-597370
Do you have any idea what is the shortest distance the 180deg twist can be safely done without degradation in belt's life? DigitalDentist reported that he has seen no degradation of the prints done with teeth running on the smooth idler. I don't know about the belt lifespan due to the teeth being compressed more than in a toothed idler. My test would suggest that the minimum distance for the 180deg twist without too much stress on the belt is 100mm for the complete twist. And I have much less than that between the carriage and the idler when it is at the end of its upper stroke. Depending on Delta design, if the upper pulley is too close to the carriage at the top position of the carriage this will reduce the life of the belt.

On the other hand, if the carriage is 3D printed, the upper belt clamp can be redesigned so that it catches the belt in its 180deg twisted position. My carriages are injection molded so not much luck here.
Here's a quick sketch with all 3 situations:

[attachment 67806 screenshot.487.png]

I assume that rarely one will print such a tall object as to reach max Z position so I guess even in my case twisting the belt on one side would be acceptable.

Another option is to use spectra for half of the loop:

[attachment 67809 screenshot.488.png]

Because of the difference in width between the belt and the spectra, the idler should be larger to compensate for the size so that the vertical lines are still parallel. I have sketched the situation where the spectra is used on the existing pulley (I will have 2 flanged bearings so if/when i change to spectra I can run it in the groove between the two bearings)]]> realthor Delta Machines Wed, 16 Dec 2015 04:31:58 -0500 https://reprap.org/forum/read.php?178,593682,597307#msg-597307 Re: Delta pulley and idler dimensions question https://reprap.org/forum/read.php?178,593682,597307#msg-597307
Then when upgrading my roller carriages to linear bearings, I changed from the belt riding on the smooth side of the idler bearings to the toothed side due to the way that the robotdigg carriages were set up.
This resulted in a noticeable degradation in quality. Sides of the piece that used to be dead flat now have slight diagonal ridges on them.

They're only noticeable in the right light, but they're definitely there. I've also noticed a bit more 'ringing' in the print, which might be due to the teeth of the belt compressing more than if the belt were flipped.

I'm going to get out the dremel and attack those robotdigg carriages to allow a half-twist in the long side of the belt, and see if I can get my old print quality back. Incidentally the reason I went to the linear slides turned out to be unrelated to what was actually going on. It turned out to be a slic3r setting.]]> nebbian Delta Machines Wed, 16 Dec 2015 02:20:25 -0500 https://reprap.org/forum/read.php?178,593682,597175#msg-597175 Re: Delta pulley and idler dimensions question https://reprap.org/forum/read.php?178,593682,597175#msg-597175
Philosophy aside, having some experience with both belts and spectra fishing line, and having read a lot about Spectra/Dyneema (at least read this Wikipedia section on Ultra High Molecular Weight Polyethylene), I can see a good approach in combining the belt for the exact portion that will roll across the toothed pulley and Spectra/Dyneema,Kevlar, UHMWP fibers for everything else, all the pulleys and 3D routing is better with spectra but the driving portion.

I am going to experiment with this approach which, by the way, is nothing new. There are a couple of videos on youtube sporting this approach, one of them (I don't remember any other) being about a Delta of all.

I know that a new variable will be introduced into the system, the tensioning of the combo, but we are clueless anyway about the right way to tension belts and we go by "feeling", so nothing new there.


Edit reason: Wow, I just learned how to link to a section of a page that doesn't got an anchor. Super cool, I have sent you right to the right section on the wikipedia page.]]> realthor Delta Machines Tue, 15 Dec 2015 15:45:34 -0500 https://reprap.org/forum/read.php?178,593682,597140#msg-597140 Re: Delta pulley and idler dimensions question https://reprap.org/forum/read.php?178,593682,597140#msg-597140
Quote
realthor
Quote
voi9viper
I just hate imprecission too. syncromesh as in trasmissions? Or is it something new, which I suspect if patents apply. I'm dating myself, but my 71 firebird had a syncromesh tranny I think.

No idea how old this is but this is it:


I have also been thinking of these kinds of chains. [www.amazon.co.uk]

They may work in our setup and they could be stronger, although not necessarily more precise.
]]> jaguarking11 Delta Machines Tue, 15 Dec 2015 14:44:54 -0500 https://reprap.org/forum/read.php?178,593682,597138#msg-597138 Re: Delta pulley and idler dimensions question https://reprap.org/forum/read.php?178,593682,597138#msg-597138
Quote
realthor
Quote
jaguarking11
I run 20T pulleys on my delta with 5mm id flanged bearings in a sandwitch. It works, however I am not happy with the arangement. I would like to run a 20T pulley with built in bearings, however I have not found any yet.

With that said, I still run rubber belts even with a heated chamber and 45-50C in there they seem to have settled down. I think a redesign of the idler side of a delta is necessary.

I have considered 20T GT2 pulley with 8mm bore and 2x MR84ZZ (4x8x3mm) bearings but I have decided that inserting those miniature bearings in the bore was too complicated and opted out for 2 flanged F694ZZ (4x11x4mm). The difference in diameter from a 20T pulley with the belt ontop is 0.3 or 0.4mm when you put the belt riding on the bearings with the teeth on the smooth surface of the bearing's OD.

I also believe that this resulting smooth pulley will be quieter than a toothed pulley but I don't know by how much (a good read here: http://www.pfeiferindustries.com/troubleshooting/timing-belt-unusual-excessive-noise.html).

I guess I'll see when they arrive.

Why are you unhappy of that arrangement? Did you notice any loss in quality on the prints?

Its not the quality that suffers. I have rarely gone to .1mm layers let along sub .1mm stuff as I 3d print larger stuff and that kind of resolution would give me print times measured in days, not hours.

With that said I am unhappy with the solution as it will create wear on the belt, I have observed that my belt lost a bit of tension creating some slack. A toothed pulley preferably of the same diameter would hold the teeth in a proper grove and increase surface area and belt life with the possible down side of increasing friction. However friction limitations are not a concern for me at this time due to the fact that I run a ramps, anything over 150mm/s causes the cpu to peg giving very jerky movements and bad prints.]]> jaguarking11 Delta Machines Tue, 15 Dec 2015 14:39:07 -0500 https://reprap.org/forum/read.php?178,593682,596245#msg-596245 Re: Delta pulley and idler dimensions question https://reprap.org/forum/read.php?178,593682,596245#msg-596245
Quote
voi9viper
I just hate imprecission too. syncromesh as in trasmissions? Or is it something new, which I suspect if patents apply. I'm dating myself, but my 71 firebird had a syncromesh tranny I think.

No idea how old this is but this is it:


]]> realthor Delta Machines Sun, 13 Dec 2015 13:28:15 -0500 https://reprap.org/forum/read.php?178,593682,596232#msg-596232 Re: Delta pulley and idler dimensions question https://reprap.org/forum/read.php?178,593682,596232#msg-596232 voi9viper Delta Machines Sun, 13 Dec 2015 13:05:31 -0500 https://reprap.org/forum/read.php?178,593682,596230#msg-596230 Re: Delta pulley and idler dimensions question https://reprap.org/forum/read.php?178,593682,596230#msg-596230
Quote
voi9viper
...The extruder is far less accurate, and I don't see huge efforts being made in that area yet, like feed forward pressure control..

I implemented pressure advance in RepRapFirmware about a year ago. Sadly, it didn't improve my print quality much. I intend to try adding extruder time advance as well sometime.]]> dc42 Delta Machines Sun, 13 Dec 2015 13:02:27 -0500 https://reprap.org/forum/read.php?178,593682,596208#msg-596208 Re: Delta pulley and idler dimensions question https://reprap.org/forum/read.php?178,593682,596208#msg-596208
Myself, I miss designing fro spectra line for its advantages but I am so sad that no development is going for the "spectra drive" that was once a hot topic in the reprap discussions, before everybody got confy and settled for timing belts. Yes, spectra drive has some disadvantages compared to timing belts but it's also silent and doesn't need toothed pulleys and some more. But the big disadvantage is its "walking" effect which is bad for precision/repetability. Synchromesh is the new kid that could but it's proprietary technology and it's difficult to source and its quite expensive so timing belts are the de facto for their ubiquity and cost effectiveness.

I went for 20tooth 5mm bore pulleys and F694ZZ flanged bearings (4x11x4mm). The difference in diameter between the two when they have belts on is 0.4mm on a 600mm height loop between the two. I too will have a 4mm smooth bolt for the idler to ride and that is 0.13mm smaller than the 4mm bearing hole but, being always forced but the tension in the belt, it will never be loose and will always have contact with the bolt.
I still have my doubts at high speeds where the belt resonates heavily, maybe that will introduce a play in the tension and will make the flanged bearing loose some of its contact with the bolt.]]> realthor Delta Machines Sun, 13 Dec 2015 11:46:42 -0500 https://reprap.org/forum/read.php?178,593682,595897#msg-595897 Re: Delta pulley and idler dimensions question https://reprap.org/forum/read.php?178,593682,595897#msg-595897 voi9viper Delta Machines Sat, 12 Dec 2015 13:59:12 -0500 https://reprap.org/forum/read.php?178,593682,595629#msg-595629 Re: Delta pulley and idler dimensions question https://reprap.org/forum/read.php?178,593682,595629#msg-595629
Quote
dc42
The toothed belt running on the smooth pulley is one of the noisiest components of my delta. I think it excites the resonant frequency of the belt at some speeds. That's why I want a better solution.

But the belt's teeth entering at high speeds into their recess on the motor pulley have an apparently worse effect of compressing the air and evacuating it at high speeds as they fill the gap, making basically a pop sound that is multiplied with speed creating the "drrrrrr" sound of the belt. I fail to see where or how can the teeth create a similar noise on the smooth pulleys.There is no place where the air would be compressed.

Could it be that each tooth, not finding a perfectly matched recess to dissipate its energy is banging into the pulley with all force? I really can't see the smooth pulley being a source of noise.]]> realthor Delta Machines Fri, 11 Dec 2015 17:20:10 -0500 https://reprap.org/forum/read.php?178,593682,595616#msg-595616 Re: Delta pulley and idler dimensions question https://reprap.org/forum/read.php?178,593682,595616#msg-595616 dc42 Delta Machines Fri, 11 Dec 2015 16:47:07 -0500 https://reprap.org/forum/read.php?178,593682,595610#msg-595610 Re: Delta pulley and idler dimensions question https://reprap.org/forum/read.php?178,593682,595610#msg-595610
Quote
jaguarking11
I run 20T pulleys on my delta with 5mm id flanged bearings in a sandwitch. It works, however I am not happy with the arangement. I would like to run a 20T pulley with built in bearings, however I have not found any yet.

With that said, I still run rubber belts even with a heated chamber and 45-50C in there they seem to have settled down. I think a redesign of the idler side of a delta is necessary.

I have considered 20T GT2 pulley with 8mm bore and 2x MR84ZZ (4x8x3mm) bearings but I have decided that inserting those miniature bearings in the bore was too complicated and opted out for 2 flanged F694ZZ (4x11x4mm). The difference in diameter from a 20T pulley with the belt ontop is 0.3 or 0.4mm when you put the belt riding on the bearings with the teeth on the smooth surface of the bearing's OD.

I also believe that this resulting smooth pulley will be quieter than a toothed pulley but I don't know by how much (a good read here: http://www.pfeiferindustries.com/troubleshooting/timing-belt-unusual-excessive-noise.html).

I guess I'll see when they arrive.

Why are you unhappy of that arrangement? Did you notice any loss in quality on the prints?]]> realthor Delta Machines Fri, 11 Dec 2015 16:37:14 -0500 https://reprap.org/forum/read.php?178,593682,595606#msg-595606 Re: Delta pulley and idler dimensions question https://reprap.org/forum/read.php?178,593682,595606#msg-595606
With that said, I still run rubber belts even with a heated chamber and 45-50C in there they seem to have settled down. I think a redesign of the idler side of a delta is necessary.]]> jaguarking11 Delta Machines Fri, 11 Dec 2015 16:28:18 -0500 https://reprap.org/forum/read.php?178,593682,594193#msg-594193 Re: Delta pulley and idler dimensions question https://reprap.org/forum/read.php?178,593682,594193#msg-594193 Now we have to buy another specialty product to add up to the vitamins of a 3D printer.

However, I don't see any issue that would arise down the road from an imperfect fit of the bolt/bearing because the tension in the belt would always load it from a single side. I know this is not "the way it's done" but neither is running the belt with the teeth on the bearing and there is no degradation in performance, as the doctor reports a few posts above. There might be applications where this would be detrimental but in this case I just don't see any downside.]]> realthor Delta Machines Tue, 08 Dec 2015 05:21:01 -0500 https://reprap.org/forum/read.php?178,593682,594189#msg-594189 Re: Delta pulley and idler dimensions question https://reprap.org/forum/read.php?178,593682,594189#msg-594189
Quote
etfrench
Misumi has them and the price seems pretty reasonable.

Europeans can't shop from Misumi though..., unless you have a registered company.]]> Koenig Delta Machines Tue, 08 Dec 2015 05:10:42 -0500 https://reprap.org/forum/read.php?178,593682,594089#msg-594089 Re: Delta pulley and idler dimensions question https://reprap.org/forum/read.php?178,593682,594089#msg-594089 etfrench Delta Machines Mon, 07 Dec 2015 21:11:33 -0500 https://reprap.org/forum/read.php?178,593682,594087#msg-594087 Re: Delta pulley and idler dimensions question https://reprap.org/forum/read.php?178,593682,594087#msg-594087
Quote
etfrench
Shoulder bolts were designed for applications like this. It isn't good practice to allow bearings to flop around on their axles. It may work with standard bolts, but it won't be as good as it can be. Why introduce a source for errors when it's not necessary?

It's quite difficult to find them at least I haven't been able to find a shop around that has them. I am in Finland so it might be different in US.]]> realthor Delta Machines Mon, 07 Dec 2015 20:50:18 -0500 https://reprap.org/forum/read.php?178,593682,594086#msg-594086 Re: Delta pulley and idler dimensions question https://reprap.org/forum/read.php?178,593682,594086#msg-594086 etfrench Delta Machines Mon, 07 Dec 2015 20:40:03 -0500 https://reprap.org/forum/read.php?178,593682,594076#msg-594076 Re: Delta pulley and idler dimensions question https://reprap.org/forum/read.php?178,593682,594076#msg-594076
I don't know for Deltas how do these values compound considering that for every move all 3 motors rotate, but with the calculated values, at 16x microstepping does it still matter if I choose 16 or 32 tooth pulleys?

@etfrench: did you choose 5mm shoulderbolt because the M5 bolt is more 4.87mm and not 5mm? I would think that even if you have 4.87mm bolt, the 5mm ID bearings will ride well on it after the tension is applied to the belt because the tension will cause a permanent contact on one side of the bolt at all times. I don't think there will be any noise caused by this or other secondary effects as long as there is enough tension on the belt. Please let me know if you do.

[attachment 67261 screenshot.483.png]]]> realthor Delta Machines Mon, 07 Dec 2015 19:46:05 -0500 https://reprap.org/forum/read.php?178,593682,593999#msg-593999 Re: Delta pulley and idler dimensions question https://reprap.org/forum/read.php?178,593682,593999#msg-593999


]]> etfrench Delta Machines Mon, 07 Dec 2015 14:45:21 -0500 https://reprap.org/forum/read.php?178,593682,593870#msg-593870 Re: Delta pulley and idler dimensions question https://reprap.org/forum/read.php?178,593682,593870#msg-593870
Quote
o_lampe
So I made some dummy 10 x 5 x 4 bearings from PLA and printed my own 22 tooth idler with real MF105 BBs.
It's a pretty close fit in the corners, next time I use 8x5x4 bearings and print smaller idlers.
-Olaf

You have to print them on a pretty darn precise 3d printer otherwise you might get errors in printed parts isn't it? I am lately printing stuff at the library where they have ultimakers but I see errors in those as well, so unless I have myself another printer that i know I keep calibrated and well maintained I'd go straight to bearings and let the toothed side ride the bearing (I wouldn't want the twisted belt to try walking away on the bearings, I can use Spectra in that case, it too walks back and forth and at least in a predictable manner).

Regarding the driving side of the belt (the one clamped to the carriage): it is mandatory that this is perfectly vertical, like I have shown in my sketch attached to the first post?

One more: I am looking at "685 685ZZW3 MR115ZZ deep groove ball bearing 5x11x3mm miniature bearing" to use for the idlers. They are pretty close to the 13mm OD of the 16-tooth GT2 pulley. The problem is that they are not flanged and being 3mm deep, a 6mm wide GT2 will require 2 of them side by side. How would you setup flanges? Washers maybe? Are the flanges absolutely necessary? AFAIK the tension on the belt will arrange it to be exactly under/over the motor pulley. The Overlord currently uses a 5mm bolt and a 20-tooth MXL brass idler pulley that rotates on the bolt.

Thanks.]]> realthor Delta Machines Mon, 07 Dec 2015 08:45:20 -0500 https://reprap.org/forum/read.php?178,593682,593850#msg-593850 Re: Delta pulley and idler dimensions question https://reprap.org/forum/read.php?178,593682,593850#msg-593850
So I made some dummy 10 x 5 x 4 bearings from PLA and printed my own 22 tooth idler with real MF105 BBs.
It's a pretty close fit in the corners, next time I use 8x5x4 bearings and print smaller idlers.
-Olaf]]> o_lampe Delta Machines Mon, 07 Dec 2015 07:32:16 -0500