i have an x min an y min and an z max endstop they are as such defined in the firmware; #ifndef ENDSTOPPULLUPS // fine endstop settings: Individual pullups. will be ignored if ENDSTOPPULLUPS is defined // #define ENDSTOPPULLUP_XMAX // #define ENDSTOPPULLUP_YMAX #define ENDSTOPPULLUP_ZMAX #define ENDSTOPPULLUP_XMIN #define ENDSTOPPULLUP_YMIN // #define ENDSTOPPULLUP_ZMIN #endif #ifdef ENDSTOPPULLUPS // #define ENDSTOPPULLUP_XMAX // #define ENDSTOPPULLUP_YMAX #define ENDSTOPPULLUP_ZMAX #define ENDSTOPPULLUP_XMIN #define ENDSTOPPULLUP_YMIN // #define ENDSTOPPULLUP_ZMIN #endif they are mechanical, so endstop inversings are on false DisableMax/Min endstops is undefined and here comes the riddle; // ENDSTOP SETTINGS: // Sets direction of endstops when homing; 1=MAX, -1=MIN #define X_HOME_DIR -1 #define Y_HOME_DIR -1 #define Z_HOME_DIR 1 when i define Z @ -1(min), it shows up in Pronterface with the m119 check endstops command as triggered, only, it says; Zmin triggerred. -1= min pos, so i tell the firmware its at the other side; @1. as defined above. and my Z endstop is gone. so the prob is that i can only define a Zmin endstop. anyone know why? https://reprap.org/forum/read.php?2,454177,454177#msg-454177 Mon, 12 Oct 2026 14:27:30 -0400 Phorum 5.2.23 https://reprap.org/forum/read.php?2,454177,459260#msg-459260 https://reprap.org/forum/read.php?2,454177,459260#msg-459260 all Max endstops were gone if defined, they didnt show up upon testing. min stops were ok.
i had to uncomment
// Disable max endstops for compatibility with endstop checking routine
//#if defined(COREXY) && !defined(DISABLE_MAX_ENDSTOPS)
// #define DISABLE_MAX_ENDSTOPS
//#endif
despite the fact that
//#define DISABLE_MAX_ENDSTOPS
//#define DISABLE_MIN_ENDSTOPS
was uncommented.
i now have all my endstops as they should be.
but.
when starting the printer up
i have to quickly command 3diffrent directions after each other,
otherwise he goes with the first command without stopping, even ignoring his endstop for a couple slips.
it seems there is indeed some incompatibility with core xy and endstops, but i cannot find why anywhere.
and if i cannot locate the problem, its hard to try and fix it..]]> Pekkie85 Developers Thu, 22 Jan 2015 19:34:50 -0500 https://reprap.org/forum/read.php?2,454177,456904#msg-456904 https://reprap.org/forum/read.php?2,454177,456904#msg-456904
I suspect the board has max endstop pins set to -1, ie diabled.

You may need to swap pin definition between z min endstop and z max endstop making z min -1 and z max what ever value z min had.]]> Dust Developers Sun, 18 Jan 2015 06:26:10 -0500 https://reprap.org/forum/read.php?2,454177,454932#msg-454932 https://reprap.org/forum/read.php?2,454177,454932#msg-454932 so firmware should do that.]]> Pekkie85 Developers Tue, 13 Jan 2015 17:32:09 -0500 https://reprap.org/forum/read.php?2,454177,454547#msg-454547 https://reprap.org/forum/read.php?2,454177,454547#msg-454547 Dust Developers Tue, 13 Jan 2015 05:25:35 -0500 https://reprap.org/forum/read.php?2,454177,454177#msg-454177 https://reprap.org/forum/read.php?2,454177,454177#msg-454177 they are as such defined in the firmware;
#ifndef ENDSTOPPULLUPS
// fine endstop settings: Individual pullups. will be ignored if ENDSTOPPULLUPS is defined
// #define ENDSTOPPULLUP_XMAX
// #define ENDSTOPPULLUP_YMAX
#define ENDSTOPPULLUP_ZMAX
#define ENDSTOPPULLUP_XMIN
#define ENDSTOPPULLUP_YMIN
// #define ENDSTOPPULLUP_ZMIN
#endif

#ifdef ENDSTOPPULLUPS
// #define ENDSTOPPULLUP_XMAX
// #define ENDSTOPPULLUP_YMAX
#define ENDSTOPPULLUP_ZMAX
#define ENDSTOPPULLUP_XMIN
#define ENDSTOPPULLUP_YMIN
// #define ENDSTOPPULLUP_ZMIN
#endif
they are mechanical, so endstop inversings are on false
DisableMax/Min endstops is undefined

and here comes the riddle;

// ENDSTOP SETTINGS:
// Sets direction of endstops when homing; 1=MAX, -1=MIN
#define X_HOME_DIR -1
#define Y_HOME_DIR -1
#define Z_HOME_DIR 1

when i define Z @ -1(min), it shows up in Pronterface with the m119 check endstops command as triggered, only, it says; Zmin triggerred.
-1= min pos, so i tell the firmware its at the other side; @1.
as defined above.
and my Z endstop is gone.

so the prob is that i can only define a Zmin endstop.
anyone know why?]]> Pekkie85 Developers Mon, 12 Jan 2015 10:48:06 -0500