High speed, high volume flow rate printing Just finished some more testing and development along the lines of this title if anyone is interested. Be warned that it is a long and somewhat involved post. [somei3deas.wordpress.com] There is an associated YouTube video. It's about 25 minutes long but the first 12 minutes or so are probably the most interesting if you are short of time. [www.youtube.com] https://reprap.org/forum/read.php?2,836161,836161#msg-836161 Sat, 14 Mar 2026 13:28:06 -0400 Phorum 5.2.23 https://reprap.org/forum/read.php?2,836161,840904#msg-840904 Re: High speed, high volume flow rate printing https://reprap.org/forum/read.php?2,836161,840904#msg-840904 deckingman Developers Mon, 10 Dec 2018 05:15:03 -0500 https://reprap.org/forum/read.php?2,836161,840902#msg-840902 Re: High speed, high volume flow rate printing https://reprap.org/forum/read.php?2,836161,840902#msg-840902
Quote
VDX
... hmmm ... MIT managed to get a patent on "laser-preheating" the filament, what we were discussing here in the forum 10 years ago ... so the patent attorneys didn't find the "prior art" infos :S

Just saw this.
Indeed you mentioned the use of a laser to heat thoroughly the filament.
Yet, what triggered my attention is the threaded nut to push the filament. I thought about a similar system but due to the dust generated by the cut envisioned devised an other way by using rollers.

Here they solved this issue by using a threaded filament ! Yet, dust should still be generated . Fast and frequent retraction is an other potential issue.

I assumed that publishing on the net would be valid as "prior art" if backed by pictures of a working device ? (Even disguised in an other "design" to fool thieves)]]> MKSA Developers Mon, 10 Dec 2018 04:50:40 -0500 https://reprap.org/forum/read.php?2,836161,840897#msg-840897 Re: High speed, high volume flow rate printing https://reprap.org/forum/read.php?2,836161,840897#msg-840897 VDX Developers Mon, 10 Dec 2018 03:04:51 -0500 https://reprap.org/forum/read.php?2,836161,840882#msg-840882 Re: High speed, high volume flow rate printing https://reprap.org/forum/read.php?2,836161,840882#msg-840882 www.3ders.org] ?

MIT's attempt to speed up printers]]> Dust Developers Sun, 09 Dec 2018 19:26:00 -0500 https://reprap.org/forum/read.php?2,836161,840850#msg-840850 Re: High speed, high volume flow rate printing https://reprap.org/forum/read.php?2,836161,840850#msg-840850
Quote
o_lampe
I must've missed that thread. Very impressive (tu)
What if you'd use one NEMA23 extruder instead of three Bondtech ( $$$ )? Approximately same weight or even less.
Would it rip out the Bowden tube?
Would it melt fast enough? (only one meltchamber instead of three). Maybe a longer melt chamber would do the trick...

It's about the melt rate. It doesn't matter how hard you try and force the filament into the hot end if you can't melt it at that rate. All that happens is that you grind away the filament at best or as you say, build up so much pressure that the Bowden tubes get forced out.

Three melt cambers give you two things. Firstly the 3 fold increase in hot surface to filament area. Secondly, each filament gets fed in at 1/3rd of the speed so the time to pass through the melt chambers is increased 3 fold for each filament.

If my maths serve me correctly, the volume melt rates I observed were higher than those reported for an E3D Volcano which uses a single, long, melt chamber.]]> deckingman Developers Sun, 09 Dec 2018 12:10:05 -0500 https://reprap.org/forum/read.php?2,836161,840090#msg-840090 Re: High speed, high volume flow rate printing https://reprap.org/forum/read.php?2,836161,840090#msg-840090 What if you'd use one NEMA23 extruder instead of three Bondtech ( $$$ )? Approximately same weight or even less.
Would it rip out the Bowden tube?
Would it melt fast enough? (only one meltchamber instead of three). Maybe a longer melt chamber would do the trick...]]> o_lampe Developers Sat, 01 Dec 2018 02:18:44 -0500 https://reprap.org/forum/read.php?2,836161,836161#msg-836161 High speed, high volume flow rate printing https://reprap.org/forum/read.php?2,836161,836161#msg-836161 [somei3deas.wordpress.com]

There is an associated YouTube video. It's about 25 minutes long but the first 12 minutes or so are probably the most interesting if you are short of time.
[www.youtube.com]]]> deckingman Developers Sun, 14 Oct 2018 09:05:10 -0400