Makerbot Endstops / Wiring Kit / RAMPS 1.4 mismatch Hello all, I'm working on my first build, a Prusa Mendel v2. I'm close to a first print. I recently received one of those "ultimate" electronics kits off of eBay, and it included, among other things: * RAMPS 1.4 * Three cables labeled "endstop" with 3-pin female connectors on either side * Three MakerBot 1.2 mechanical endstops I didn't closely inspect these items until tonight, and I've got an issue. RAMPS 1.4 expects three pins. The 3-pin cable expects three pins. But the MakerBot endstops... wait for it... have four pins. It looks to me like I'm going to have to do some manual rewiring, as the MakerBot endstops have two ground pins in the center. One of those ground pins seem to be the superfluous pin. That is, unless I'm missing something important. Your thoughts? Thanks, Brad https://reprap.org/forum/read.php?219,160740,160740#msg-160740 Tue, 09 Jun 2026 13:52:02 -0400 Phorum 5.2.23 https://reprap.org/forum/read.php?219,160740,835540#msg-835540 Re: Makerbot Endstops / Wiring Kit / RAMPS 1.4 mismatch https://reprap.org/forum/read.php?219,160740,835540#msg-835540 Its one of those things where it looks all cool at first, then you realize its just fluff. The plain switches are smaller footprint too, so better IMO.]]> jmaeding RAMPS Electronics Thu, 04 Oct 2018 18:04:52 -0400 https://reprap.org/forum/read.php?219,160740,835532#msg-835532 Re: Makerbot Endstops / Wiring Kit / RAMPS 1.4 mismatch https://reprap.org/forum/read.php?219,160740,835532#msg-835532 How to make these Mechanical Endstop V1.2 normaly connected?
with:
X_MIN_ENDSTOP_INVERTING = false its permanently triggered i see it with m119
X_MIN_ENDSTOP_INVERTING = True is working perfectly after I disconnected the wire and it was working . so its in normaly open mode

using an ampmeter with black on COM and red on NC it gives connected signal and stops when microswitch closes at the same time led lights which is a normal behaviour for NC

Any ideas how to make this switch NC instead of NO?

Im on the verge of sacrificing one endstop and start cuting things]]> MauDaFaca RAMPS Electronics Thu, 04 Oct 2018 17:22:37 -0400 https://reprap.org/forum/read.php?219,160740,782410#msg-782410 Re: Makerbot Endstops / Wiring Kit / RAMPS 1.4 mismatch https://reprap.org/forum/read.php?219,160740,782410#msg-782410 max123 RAMPS Electronics Tue, 08 Aug 2017 13:46:05 -0400 https://reprap.org/forum/read.php?219,160740,504290#msg-504290 Re: Makerbot Endstops / Wiring Kit / RAMPS 1.4 mismatch https://reprap.org/forum/read.php?219,160740,504290#msg-504290
I'm using Ramps 1.4 with marlin on it.
I have the Mechanical Endstops v1.2 as shown on all the images in this thread.

I have the wiring figured out and learned the Vcc might Work, or not, depending on quality.

How to test endstop using Multimeter? I do not know what to look for.

What I do not know for sure is the firmware settings:

I do offcourse need make sure endstops are enabled, then:

I do the following as the endstops have pullups on board, so disabling the RAMPS onboard pullup resistors.
// #define ENDSTOPPULLUPS

I don't know if I need to set this to true or false, and what the consequences could be?
// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
const bool X_MIN_ENDSTOP_INVERTING = false;
const bool Y_MIN_ENDSTOP_INVERTING = false;
const bool Z_MIN_ENDSTOP_INVERTING = false;
const bool X_MAX_ENDSTOP_INVERTING = false;
const bool Y_MAX_ENDSTOP_INVERTING = false
const bool Z_MAX_ENDSTOP_INVERTING = false;

I have 6 endstops, so planning on using all 6 like so:
#define DISABLE_MAX_ENDSTOPS
#define DISABLE_MIN_ENDSTOPS]]> dintid RAMPS Electronics Sat, 02 May 2015 08:13:42 -0400 https://reprap.org/forum/read.php?219,160740,502253#msg-502253 Re: Makerbot Endstops / Wiring Kit / RAMPS 1.4 mismatch https://reprap.org/forum/read.php?219,160740,502253#msg-502253 The thing to be careful about is whatt wires go to what pins. I recall that the only thing you can mess up if no circuit board, is the normally closed or open, which is easy to reverse in the config file.
Be careful here, and look at the wiki for "normal" setup without a board. email me at jmaeding123 you know the symbol hunsaker dot com (remove the 123) if you want help.
thx]]> jmaeding RAMPS Electronics Sun, 26 Apr 2015 23:11:52 -0400 https://reprap.org/forum/read.php?219,160740,502224#msg-502224 Re: Makerbot Endstops / Wiring Kit / RAMPS 1.4 mismatch https://reprap.org/forum/read.php?219,160740,502224#msg-502224 reao RAMPS Electronics Sun, 26 Apr 2015 19:47:57 -0400 https://reprap.org/forum/read.php?219,160740,500687#msg-500687 Re: Makerbot Endstops / Wiring Kit / RAMPS 1.4 mismatch https://reprap.org/forum/read.php?219,160740,500687#msg-500687 jmaeding RAMPS Electronics Thu, 23 Apr 2015 12:05:19 -0400 https://reprap.org/forum/read.php?219,160740,500525#msg-500525 Re: Makerbot Endstops / Wiring Kit / RAMPS 1.4 mismatch https://reprap.org/forum/read.php?219,160740,500525#msg-500525 reao RAMPS Electronics Thu, 23 Apr 2015 01:06:28 -0400 https://reprap.org/forum/read.php?219,160740,500510#msg-500510 Re: Makerbot Endstops / Wiring Kit / RAMPS 1.4 mismatch https://reprap.org/forum/read.php?219,160740,500510#msg-500510
You probably shorted +5V and Gnd and that fried the regulator on the Arduino and possibly the Mega chip, but the RAMPS and stepper drivers should have survived.]]> AndrewBCN RAMPS Electronics Wed, 22 Apr 2015 21:56:07 -0400 https://reprap.org/forum/read.php?219,160740,500489#msg-500489 Re: Makerbot Endstops / Wiring Kit / RAMPS 1.4 mismatch https://reprap.org/forum/read.php?219,160740,500489#msg-500489 reao RAMPS Electronics Wed, 22 Apr 2015 20:59:07 -0400 https://reprap.org/forum/read.php?219,160740,377217#msg-377217 Re: Makerbot Endstops / Wiring Kit / RAMPS 1.4 mismatch https://reprap.org/forum/read.php?219,160740,377217#msg-377217
My first drawing, in this thread, with three wires, works.
Early in this thread, Bobc's comments are good things to read. His comments describe differences between manufacturers, the how's & why's of some of the confusion. He talks about testing. These are all good things. If you have doubts, reading his comments a few times, then test. I found that a lower voltage battery works well.

Our friend jmaeding's configurations for your config file should be referenced.

My second drawing is taken from early Ramps 1.4 schematics and works, though things may be confusing on the config end.

The fellow from nathionaleventphotography's images work.

Hope all this makes sense, that things work out and there is no blue smoke
ken]]> kenwilliams RAMPS Electronics Wed, 02 Jul 2014 12:38:37 -0400 https://reprap.org/forum/read.php?219,160740,377202#msg-377202 Re: Makerbot Endstops / Wiring Kit / RAMPS 1.4 mismatch https://reprap.org/forum/read.php?219,160740,377202#msg-377202
Still confused what is right.

Is there a latest correct drawing avaliable like from KennWiliams or maybe this one is correct?]]> hgestel RAMPS Electronics Wed, 02 Jul 2014 11:53:32 -0400 https://reprap.org/forum/read.php?219,160740,369954#msg-369954 Re: Makerbot Endstops / Wiring Kit / RAMPS 1.4 mismatch https://reprap.org/forum/read.php?219,160740,369954#msg-369954
[attachment 34944 endstop_wiring.jpg]]]> nationaleventphotography@gmail.com RAMPS Electronics Sat, 14 Jun 2014 19:55:02 -0400 https://reprap.org/forum/read.php?219,160740,349656#msg-349656 Re: Makerbot Endstops / Wiring Kit / RAMPS 1.4 mismatch https://reprap.org/forum/read.php?219,160740,349656#msg-349656
[forums.reprap.org]

They light up when pressed and my megatronics is smoke free. Looks like this wiring works for sainsmart endstops/megatronics setup]]> BillC RAMPS Electronics Sat, 03 May 2014 12:24:05 -0400 https://reprap.org/forum/read.php?219,160740,310039#msg-310039 Re: Makerbot Endstops / Wiring Kit / RAMPS 1.4 mismatch https://reprap.org/forum/read.php?219,160740,310039#msg-310039 Be sure your configuration.h file has:
#define ENDSTOP_PULLUP_X_MIN true
#define ENDSTOP_PULLUP_Y_MIN true
#define ENDSTOP_PULLUP_Z_MIN true
#define ENDSTOP_PULLUP_X_MAX true
#define ENDSTOP_PULLUP_Y_MAX true
#define ENDSTOP_PULLUP_Z_MAX true

for any endstops, I only use 3 for min limits, the max items here do nothing if no switches.

For those wishing me luck on my startup, it went ok, but my RAMPS board x axis is messed up, it causes the driver and motor to heat up fast.
It behaves otherwise. I tested on other motors, drivers, cables, and its not them. I killed a driver this way.
So I switched x axis pins in pins.h to spare extruder 2, and moved the (new) driver and stepper cable to extruder 2.
EXCEPT, the driver got plugged in one pin off.
Power on, smoke rising....
New mega on its way from Amazon Prime, 2 days.

The funny thing is the mega behaves ok without ramps power on. I can upload firmware fine.
As soon as ramps power supply is plugged in, the mega is unrecognized by windows.
I nuked the power handler on the mega it seems, it did not like the shock therapy.
I didn't like it either, glad I don't have one of those integrated mega/ramps boards.]]> jmaeding RAMPS Electronics Wed, 12 Feb 2014 13:16:30 -0500 https://reprap.org/forum/read.php?219,160740,306322#msg-306322 Re: Makerbot Endstops / Wiring Kit / RAMPS 1.4 mismatch https://reprap.org/forum/read.php?219,160740,306322#msg-306322
ken]]> kenwilliams RAMPS Electronics Tue, 04 Feb 2014 19:49:28 -0500 https://reprap.org/forum/read.php?219,160740,306319#msg-306319 Re: Makerbot Endstops / Wiring Kit / RAMPS 1.4 mismatch https://reprap.org/forum/read.php?219,160740,306319#msg-306319 I did a wood frame instead of threaded rod, as I have lots of wood and tools to cut it.
The "wings" that connect vert frame to y axis also give a place for power supply.
Hope it does not burn down when I start it up. Time will tell.]]> jmaeding RAMPS Electronics Tue, 04 Feb 2014 19:35:51 -0500 https://reprap.org/forum/read.php?219,160740,306268#msg-306268 Re: Makerbot Endstops / Wiring Kit / RAMPS 1.4 mismatch https://reprap.org/forum/read.php?219,160740,306268#msg-306268 Cefiar RAMPS Electronics Tue, 04 Feb 2014 17:24:15 -0500 https://reprap.org/forum/read.php?219,160740,306079#msg-306079 Re: Makerbot Endstops / Wiring Kit / RAMPS 1.4 mismatch https://reprap.org/forum/read.php?219,160740,306079#msg-306079
If I go back, and review all the posts in this forum, there are great points and suggestions. There are also great questions. There are obscure, less obvious answers - bobc pointed out that many devices, which find their way to the market, are often fabricated through direct copy, by people whose primary language is that of commerce, and not the somewhat common english. Often there are misunderstandings in identification. A dot (possibly ) indicating a pin number could be one. Or rearranging pin designation labels in different numeric order. I found a seller's website with this problem which created the confusion and the incorrect sketch. Their device was a perfect copy of the original design. Their screened ( printed ) references contradicted the original, as did their reference sheet pin-outs.

In private correspondence with karmavore, he mentioned that it is our responsibility to research, test, research, test, then act. There is an inherent risk in what we connect. jmaeding makes similar comments. Good thoughts. This is one of those rarely mentioned pieces in the forum. Much like Edison, everyone is figuring out over a thousand ways, how not to make a 3D printer... but somewhere out there, the journey becomes the better experience than the destination

Please use the last illustration as a guide. If, and only if you feel brave, test the VCC pins on the Mechanical Endstop boards. You might possibly connect them to your RAMPS. Remember, when I tested mine, using Bobc's suggestion, a couple of AAA batteries, they heated up too fast, implying there was little, if any resistance.on the devices I got in the mail. That could further damage your components, most likely the Mega controller board.

Possibly there is a philosophical `Rule' here.

If a component within a set of connected components fails, It shall be the most expensive component which fails first.


Let me know how things work out on your printer. I tend to think everyone involved with this forum, yourself included, hopes for the best, to see a lot of success in bringing our fabrications to life.

Thanks for your comments...
Cheers!

ken]]> kenwilliams RAMPS Electronics Tue, 04 Feb 2014 12:52:39 -0500 https://reprap.org/forum/read.php?219,160740,306042#msg-306042 Re: Makerbot Endstops / Wiring Kit / RAMPS 1.4 mismatch https://reprap.org/forum/read.php?219,160740,306042#msg-306042 Hang in there, but realize I did not misunderstand your thought, which I compliment you on being able to express through another language.
I stand by the idea that people should post whatever they want, and state their experience the best they can.
It sounds like both of us are at the same stage, starting up the electronics. I wish you luck and do the same for me :)]]> jmaeding RAMPS Electronics Tue, 04 Feb 2014 11:49:44 -0500 https://reprap.org/forum/read.php?219,160740,305827#msg-305827 Re: Makerbot Endstops / Wiring Kit / RAMPS 1.4 mismatch https://reprap.org/forum/read.php?219,160740,305827#msg-305827 I had followed!
Remove came to late. I have made ​​you not blame. It should be a hint, sometimes less is more.
One wrong sktech is still on, attachment on Post. Exactly this I unfortunately caught.

@jmaeding
I wrote "please don't misunderstand", you do it!]]> aquapro RAMPS Electronics Tue, 04 Feb 2014 04:09:24 -0500 https://reprap.org/forum/read.php?219,160740,305436#msg-305436 Re: Makerbot Endstops / Wiring Kit / RAMPS 1.4 mismatch https://reprap.org/forum/read.php?219,160740,305436#msg-305436 Surely you do not come to discussion forums expecting every post to be an answer.
The nature of forums is trial and error, and drawings (even wrong ones) help that process, not hurt it.
Ken's communication has been clear, not ultimate answers every time, which is all we could ask.
Actually, I did ask for more sketches, or a book of them if Ken is willing :)
I encourage you to do the same, say "this seemed to work, but can anyone comment"....if you are unsure.

The posts about not connecting anything to the VCC pin of RAMPS 1.4 boards are the results of the discussions as I understood them.]]> jmaeding RAMPS Electronics Mon, 03 Feb 2014 12:27:28 -0500 https://reprap.org/forum/read.php?219,160740,305412#msg-305412 Re: Makerbot Endstops / Wiring Kit / RAMPS 1.4 mismatch https://reprap.org/forum/read.php?219,160740,305412#msg-305412 I am disappointed to learn about your issue.
Had you had followed this forum, you would discover that the 24 Jan 14 illustration posted the 24th. has been removed.
That posted illustration was based on the generic manufacturer's references posted on the web.

THAT INFORMATION IS AND WAS INCORRECT.

The 24 Jan 14 illustration removed.
There are any number of later posts to this forum following up, identifying issues.
I tried to correct the misinformation with an illustration posted 28 Jan 14. This illustration works.

Hopefully, replacing an affordable RAMPS board is easily remedied, and everything else goes well.

Cheers,
ken]]> kenwilliams RAMPS Electronics Mon, 03 Feb 2014 11:38:39 -0500 https://reprap.org/forum/read.php?219,160740,305220#msg-305220 Re: Makerbot Endstops / Wiring Kit / RAMPS 1.4 mismatch https://reprap.org/forum/read.php?219,160740,305220#msg-305220
I've used sketch from 24 jan (with switches from saintsmart, Signal with dot) and break my arduino. :(
PLEASE don't post many sketches, its's too confusing what is right and what is wrong.
Ken, please don't misunderstand! :)-D

Tino]]> aquapro RAMPS Electronics Mon, 03 Feb 2014 04:58:54 -0500 https://reprap.org/forum/read.php?219,160740,302922#msg-302922 Re: Makerbot Endstops / Wiring Kit / RAMPS 1.4 mismatch https://reprap.org/forum/read.php?219,160740,302922#msg-302922 jmaeding RAMPS Electronics Wed, 29 Jan 2014 11:57:54 -0500 https://reprap.org/forum/read.php?219,160740,302706#msg-302706 Re: Makerbot Endstops / Wiring Kit / RAMPS 1.4 mismatch https://reprap.org/forum/read.php?219,160740,302706#msg-302706
Thank you for your comments. More importantly, your help and explanation.
I shall contact the forum co-ordinator and see if the second sketch can be pulled. It needs to disappear.
If you think we could provide a better reference & guide, let me know. I would love to have a `clean, clear' illustration for reference.

Sincerely
ken]]> kenwilliams RAMPS Electronics Wed, 29 Jan 2014 00:47:30 -0500 https://reprap.org/forum/read.php?219,160740,302703#msg-302703 Re: Makerbot Endstops / Wiring Kit / RAMPS 1.4 mismatch https://reprap.org/forum/read.php?219,160740,302703#msg-302703
DO NOT use either sketches posted on 22 jan 14 or 24 jan 14 as reference.

There is a `lag time' between when something is posted, where it goes, how quickly people reference and respond. Some skim a post, or fail to catch a clarification/correction in later ones. There have been some folks who missed the mention the quest for answers and information. Same thing with the second sketch which was based on initial responses to the first. The intention was to document the means to connect generic Mechanical Endstops with RAMPS 1.4. Currently, I question if that can be accomplished in this specific combination.

DO NOT use either sketches posted on 22 jan 14 or 24 jan 14 as reference.

PLEASE READ bobc's earlier responses. His comments make sense of it all. I have since used a battery source, per advice. The best thing said was only use the Signal pin and the Gnd Pin on the generic Mechanical Endstop devices(s) - either endstop device #2 or #3 pin. Things will be fine & work. The battery test is smart & has little probabilty of damaging the endstop device. Things made sense with a Multimeter. The issue is the amount of electricity which flows between the Signal and the Vcc on endstops in my possession. Too much, too soon. No wonder there are boards burning out.I managed to get the LED to light, connecting the Vcc. However things got too hot too fast i.e. a lot of current was going through there. The weak link in the circuit is not on the RAMPS, it is on the Arduino Controller, which destructs quickly. Based on the recent post, it is prudent to ignore connecting the Vcc pins on either the RAMPS or endstop device.

Today, I tried calling MakerBot to visit with someone in Engineering & Design, in hopes of hearing what they were thinking and the basis of the Vers 1.2 Mech Endstop. http://www.thingiverse.com/thing:4971 After phone shuffling, it was suggested I send an e-mail request to their PR Department. My thinking was that their endstop device was designed for the controller they used. Their devices may handle certain loads, which a RAMPS/MEGA combination may not be capable of sustaining.

Please use the information contained in the Sketch dated 27Jan14. It:
- incorporates the most current comments to date
- ignores connecting Vcc ( on some RAMPS 1.4 identified as "+" ) and Vcc on generic Mechanical Endstop devices. Do we really need a LED telling you it is doing something?
- identifies the simple option of using a part of the device, the Switch, as originally identified in the RAMPS 1.4 wiki

A lot of people are referencing this Forum. Based on recent comments, I am posting what is hopefully the LAST Sketch. The intention was to identify a way of using generic Mechanical Endstops with a RAMPS 1.4 board. Looking at the participation and comments on this Forum, much of that has occurred. This sketch is posted in hopes people will reference this, and the previous ones shall be ignored.


[attachment 25869 endstop27jan14.jpg]



This SUPERSEDES Sketches posted on 24 Jan 14 and 22 Jan 14.
DO NOT USE THOSE SKETCHES AS REFERENCES

Thanks to bobc, jmaeding, Cefair, CanCakes, vreighen for their help and comments.

ken]]> kenwilliams RAMPS Electronics Wed, 29 Jan 2014 00:38:38 -0500 https://reprap.org/forum/read.php?219,160740,302668#msg-302668 Re: Makerbot Endstops / Wiring Kit / RAMPS 1.4 mismatch https://reprap.org/forum/read.php?219,160740,302668#msg-302668
I am still puzzled why you rejected your original sketch, as it was correct. The sketch does not mention pin 1, although your post did, and that is where the confusion seems to have crept in. Anyway, that is water under the bridge.

I would say forget about pin numbers, it is the pin function we are concerned with. "Pin 1" is a movable feast, so doesn't necessarily help to disambiguate.

The second sketch is I believe incorrect and is NOT SAFE to connect. Unfortunately it is now spreading around the forums and appears in Google searches. It would be really great if you could find away to remove it. You also have posts saying that the first sketch is incorrect, which is also misleading.

I appreciate your attempt to help, and the diagrams are beautifully drawn, but in this case it is leading to more confusion.]]> bobc RAMPS Electronics Tue, 28 Jan 2014 20:36:56 -0500 https://reprap.org/forum/read.php?219,160740,302310#msg-302310 Re: Makerbot Endstops / Wiring Kit / RAMPS 1.4 mismatch https://reprap.org/forum/read.php?219,160740,302310#msg-302310
Quote
CanCakes
Although the board itself says v1.1, the page on thingiverse (http://www.thingiverse.com/thing:4971) is titled "Mechanical Endstop 1.2. And on the board, it says to refer to "wiki.makerbot.com/me1" for instructions. (I think the site doesn't exist anymore, is it down for everyone or just me?)

It's not just you. I tried the Internet WayBack Machine, and it only had one archived copy (from 2/22/2010):

http://wiki.makerbot.com/me1]https://web.archive.org/web/20100222023640/[wiki.makerbot.com][/url]

Mechanical Endstop v1.x
coming soon!

Oh, well..... :(]]> vreihen RAMPS Electronics Tue, 28 Jan 2014 06:17:14 -0500 https://reprap.org/forum/read.php?219,160740,302218#msg-302218 Re: Makerbot Endstops / Wiring Kit / RAMPS 1.4 mismatch https://reprap.org/forum/read.php?219,160740,302218#msg-302218
Most of those CDROM cables had 2 shields wired to the centre pins, and 2 signals (one Red, One white). The Red one made the most sense to be +VCC, which left the White as the signal. Cheaper cables didn't bother with 2 shields (only using 1 ground pin each end) but of course, there was no standard as to which middle pin was wired as ground, so they still needed to both be there.]]> Cefiar RAMPS Electronics Tue, 28 Jan 2014 02:53:09 -0500