Somebody help with a copy CONFIGURATION.H / ADV.H and PINS.H Hallo all, I can't figure it out (for a long time now). I have a 1gen mendel with RAMPS 1.4 and the nieuw merlin firmware. I try olmost every firmware that i find, whit no resulds. in pronterface the steppers will move to 1 direktion. Can somebody look to my file's or can sent my a copy of yours so that i can compare. manny thangs to all Aldrik [attachment 10412 PINS.H.pdf] [attachment 10413 CONFIGURATION.ADV.H.pdf] [attachment 10414 CONFIGURATION.H.pdf] https://reprap.org/forum/read.php?219,161981,161981#msg-161981 Fri, 09 Oct 2026 00:21:26 -0400 Phorum 5.2.23 https://reprap.org/forum/read.php?219,161981,164124#msg-164124 Re: Somebody help with a copy CONFIGURATION.H / ADV.H and PINS.H https://reprap.org/forum/read.php?219,161981,164124#msg-164124 nonaak RAMPS Electronics Sat, 03 Nov 2012 14:55:45 -0400 https://reprap.org/forum/read.php?219,161981,164122#msg-164122 Re: Somebody help with a copy CONFIGURATION.H / ADV.H and PINS.H https://reprap.org/forum/read.php?219,161981,164122#msg-164122
The problem of the X,Y and Z is solved,thanks

Now i have to try to make the extruder motor work. the motor do nothing.

Thanks for the replies]]> nonaak RAMPS Electronics Sat, 03 Nov 2012 14:39:21 -0400 https://reprap.org/forum/read.php?219,161981,164079#msg-164079 Re: Somebody help with a copy CONFIGURATION.H / ADV.H and PINS.H https://reprap.org/forum/read.php?219,161981,164079#msg-164079 jbernardis RAMPS Electronics Sat, 03 Nov 2012 03:04:53 -0400 https://reprap.org/forum/read.php?219,161981,164070#msg-164070 Re: Somebody help with a copy CONFIGURATION.H / ADV.H and PINS.H https://reprap.org/forum/read.php?219,161981,164070#msg-164070
This may be a problem of Optosensors

For Marlin firmware, Send the Gcode M119 to view the status of the Optosensors, if it shows irregularly you need to change the Endstop settings in config.h just say -1 to 1 or false to true

For example, if the endstop sensed the optosensor the value should be High if you send M119, if it shows low then there should be problem in the codings in config.h and you need to work on Endstop settings to invert the values]]> GowthamJGR RAMPS Electronics Sat, 03 Nov 2012 01:40:32 -0400 https://reprap.org/forum/read.php?219,161981,161981#msg-161981 Somebody help with a copy CONFIGURATION.H / ADV.H and PINS.H https://reprap.org/forum/read.php?219,161981,161981#msg-161981
I can't figure it out (for a long time now).
I have a 1gen mendel with RAMPS 1.4 and the nieuw merlin firmware.
I try olmost every firmware that i find, whit no resulds.
in pronterface the steppers will move to 1 direktion.

Can somebody look to my file's or can sent my a copy of yours so that i can compare. manny thangs to all

Aldrik

[attachment 10412 PINS.H.pdf]
[attachment 10413 CONFIGURATION.ADV.H.pdf]
[attachment 10414 CONFIGURATION.H.pdf]]]> nonaak RAMPS Electronics Sun, 21 Oct 2012 17:13:29 -0400