Ramps 1.4 no lights or power with Xbox 203W Hi all, I attach my Arduino and Ramps board together and connect it to my laptop via USB. From here, I obtain lights on both boards and successfully upload Marlin firmware. I then plug in my LCD screen and have limited functions as nothing is connected. Here is where it all goes wrong... I take my Xbox Power Supply that is 203W and connect it to the ramps board. I unplug the USB and plug the Xbox PSU into the wall, nothing. No lights, no screen connectivity, nothing. I take a multimeter and connect it to the tops of the screws on the ramps board and I'm getting 12V. I'm at a loss with this. To summarize, there is no response on Ramps 1.4 when I connect it via the Xbox PSU. Can anybody help me out? Thanks!! https://reprap.org/forum/read.php?219,317785,317785#msg-317785 Mon, 05 Oct 2026 23:10:11 -0400 Phorum 5.2.23 https://reprap.org/forum/read.php?219,317785,318776#msg-318776 Re: Ramps 1.4 no lights or power with Xbox 203W https://reprap.org/forum/read.php?219,317785,318776#msg-318776
Note: Do NOT plug in the PSU to the RAMPS board for either of the following tests, and make sure USB is also disconnected.

I would try removing RAMPS from the Mega and powering just the Mega via the DC barrel jack from a plugpack. If that doesn't work (no lights), the on-board regulator on the Mega is dead.

If it does work, unplug the plugpack, put RAMPS back on it (no PSU, heated bed or hot end connected), and then plug the plugpack back into the DC barrel jack and try running it that way. If THAT works, then most likely the diode D1 on the RAMPS board is faulty.]]> Cefiar RAMPS Electronics Sun, 02 Mar 2014 18:15:40 -0500 https://reprap.org/forum/read.php?219,317785,318723#msg-318723 Re: Ramps 1.4 no lights or power with Xbox 203W https://reprap.org/forum/read.php?219,317785,318723#msg-318723
Quote
REPRAP SQUAD
Have you connected the wires on the xbox power supply correctly in order to take the psu out of standby? I have a complete tutorial on how to properly setup an xbox 360 psu to a ramps as well as other boards. Also check to see if your xbox psu is an authentic Microsoft unit or a chinese knock off as they have been known to be problematic.

Heres the direct link to the tutorial: [reprapsquad.wordpress.com]

Hi, I followed that exact guide. I had tis power supply from my first Xbox 360, so I assume it is the authentic Microsoft one.

Ramps 1.4 and the LCD screen only work off USB power. Any help?]]> TurnerChris RAMPS Electronics Sun, 02 Mar 2014 16:31:45 -0500 https://reprap.org/forum/read.php?219,317785,318722#msg-318722 Re: Ramps 1.4 no lights or power with Xbox 203W https://reprap.org/forum/read.php?219,317785,318722#msg-318722
Quote
NewPerfection
Do you have D1 installed? [reprap.org]
Hi, Yes it has the two diodes installed.]]> TurnerChris RAMPS Electronics Sun, 02 Mar 2014 16:30:35 -0500 https://reprap.org/forum/read.php?219,317785,318282#msg-318282 Re: Ramps 1.4 no lights or power with Xbox 203W https://reprap.org/forum/read.php?219,317785,318282#msg-318282
Heres the direct link to the tutorial: [reprapsquad.wordpress.com]]]> REPRAP SQUAD RAMPS Electronics Sat, 01 Mar 2014 21:35:52 -0500 https://reprap.org/forum/read.php?219,317785,318206#msg-318206 Re: Ramps 1.4 no lights or power with Xbox 203W https://reprap.org/forum/read.php?219,317785,318206#msg-318206 reprap.org]]]> NewPerfection RAMPS Electronics Sat, 01 Mar 2014 16:31:18 -0500 https://reprap.org/forum/read.php?219,317785,317785#msg-317785 Ramps 1.4 no lights or power with Xbox 203W https://reprap.org/forum/read.php?219,317785,317785#msg-317785
I attach my Arduino and Ramps board together and connect it to my laptop via USB. From here, I obtain lights on both boards and successfully upload Marlin firmware.

I then plug in my LCD screen and have limited functions as nothing is connected.

Here is where it all goes wrong...
I take my Xbox Power Supply that is 203W and connect it to the ramps board. I unplug the USB and plug the Xbox PSU into the wall, nothing. No lights, no screen connectivity, nothing.

I take a multimeter and connect it to the tops of the screws on the ramps board and I'm getting 12V.

I'm at a loss with this.

To summarize, there is no response on Ramps 1.4 when I connect it via the Xbox PSU.




Can anybody help me out?

Thanks!!]]> TurnerChris RAMPS Electronics Fri, 28 Feb 2014 18:22:31 -0500