Morning all. Please forgive me if this has been asked before but I cannot find an answer I have a CTC printer but I am making my own (I find making stuff myself somewhat rewarding) Don't have all the items yet but have started with the brains. I will be using a Arduino mega2560 and a RAMPS 1.4 (from the bay) and a smart controller with LCD but I have concerns about the ramps, inperlicular the Diode's D2 is in place but no D1. I have read this (http://reprap.org/wiki/RAMPS_1.4) but I’m a little confused It says " D1 should only be installed if the 5A rail is powered by 12V. It can be omitted and the Arduino will be powered from USB. You will want D1 installed if you add components to print without a PC. To reiterate, D1 MUST be omitted if you are powering the 5A rail by more than 12V, or the power is not absolutely clean, otherwise you may damage your ramps. " I plane to run both boards from a converted PC power supply My ? is do I need to install D1? If so can anyone tell me the value please (D2 is fitted with the value face down) I have 4001 and 4007 but I think it may need a 4004 Can someone please advise me as to whether it should be fitted or not and if fitted the value? Thanks for looking https://reprap.org/forum/read.php?219,609791,609791#msg-609791 Wed, 12 Aug 2026 01:39:10 -0400 Phorum 5.2.23 https://reprap.org/forum/read.php?219,609791,610393#msg-610393 https://reprap.org/forum/read.php?219,609791,610393#msg-610393 The mega doesn’t have any way to separate these two supplies.

Also the unused servo 5v terminals are not connected to anything without the appropriate jumper.

I really would advise not to do this if you ever intend to use a USB cable. (unless you cut the appropriate 5v line on the megas USB )]]> Dust RAMPS Electronics Sat, 16 Jan 2016 05:31:23 -0500 https://reprap.org/forum/read.php?219,609791,610369#msg-610369 https://reprap.org/forum/read.php?219,609791,610369#msg-610369 5V goes to +/- pins of an unused servo terminal, 12V to the green plug.
You can even use the 5V standby rail of the PSU and switch the Ramps on/off by software. ( Not exactly sure how, better search the forum )
-Olaf]]> o_lampe RAMPS Electronics Sat, 16 Jan 2016 03:54:21 -0500 https://reprap.org/forum/read.php?219,609791,610156#msg-610156 https://reprap.org/forum/read.php?219,609791,610156#msg-610156 Just been surfing and found a 750w pc power supply and the 12v rail is 37a at a bargain price would this be suitable ?]]> Suggy RAMPS Electronics Fri, 15 Jan 2016 13:28:52 -0500 https://reprap.org/forum/read.php?219,609791,609904#msg-609904 https://reprap.org/forum/read.php?219,609791,609904#msg-609904
Long boring discussion here if you want to read it [forum.arduino.cc]]]> Dust RAMPS Electronics Fri, 15 Jan 2016 04:48:59 -0500 https://reprap.org/forum/read.php?219,609791,609891#msg-609891 https://reprap.org/forum/read.php?219,609791,609891#msg-609891 Do at your own risk :)
-Olaf]]> o_lampe RAMPS Electronics Fri, 15 Jan 2016 04:19:46 -0500 https://reprap.org/forum/read.php?219,609791,609888#msg-609888 https://reprap.org/forum/read.php?219,609791,609888#msg-609888 I take it its still safe to connect my pc with the ramps powerd up]]> Suggy RAMPS Electronics Fri, 15 Jan 2016 04:12:11 -0500 https://reprap.org/forum/read.php?219,609791,609797#msg-609797 https://reprap.org/forum/read.php?219,609791,609797#msg-609797
It must be removed if you use more than 12v on the 5amp circuit as the standard mega cannot take more than 12v.

If you intend to print without a computer and are running 12v, you need it.

Its a 1N4004]]> Dust RAMPS Electronics Thu, 14 Jan 2016 21:53:30 -0500 https://reprap.org/forum/read.php?219,609791,609791#msg-609791 https://reprap.org/forum/read.php?219,609791,609791#msg-609791
I have a CTC printer but I am making my own (I find making stuff myself somewhat rewarding)
Don't have all the items yet but have started with the brains. I will be using a Arduino mega2560 and a RAMPS 1.4 (from the bay) and a smart controller with LCD but I have concerns about the ramps, inperlicular the Diode's
D2 is in place but no D1. I have read this (http://reprap.org/wiki/RAMPS_1.4) but I’m a little confused

It says
" D1 should only be installed if the 5A rail is powered by 12V. It can be omitted and the Arduino will be powered from USB. You will want D1 installed if you add components to print without a PC. To reiterate, D1 MUST be omitted if you are powering the 5A rail by more than 12V, or the power is not absolutely clean, otherwise you may damage your ramps. "


I plane to run both boards from a converted PC power supply

My ? is do I need to install D1? If so can anyone tell me the value please (D2 is fitted with the value face down)
I have 4001 and 4007 but I think it may need a 4004

Can someone please advise me as to whether it should be fitted or not and if fitted the value?

Thanks for looking]]> Suggy RAMPS Electronics Thu, 14 Jan 2016 21:11:56 -0500