Prusa i3 stopping mid print*video* Hi guys, I need some help. My printer have been working flawless for a long time. Suddenly it started acting strange. Stopping mid print and the steppers did not answer until a reboot of the printer. I tried: New arduino new ramps with new drivers re flash firmware with auto bed leveling re flash stock firmware (makerfarm) disable bed leveling servo new PSU re install computer software new computer fresh install new USB cable printing from SD card all doing the same. Can a stepper gone bad? they sound and work very fine when I do the pre-print movements but it will only print for a little while then quit. Sometimes a sudden stop or sometimes a sort of down stepping like its buffering more and more moving slower and slower. Sometimes the motors squeal instead of move after I stopped the print. A reboot and they move fine again. Heaters are "on" but cooling... it seems to think it's still going but it's not :S see video of example. (Never mind it not extruding at the moment, slipping on the filament) [www.youtube.com] Very grateful for help :) https://reprap.org/forum/read.php?262,359759,359759#msg-359759 Mon, 14 Sep 2026 23:55:02 -0400 Phorum 5.2.23 https://reprap.org/forum/read.php?262,359759,376094#msg-376094 Re: Prusa i3 stopping mid print*video* https://reprap.org/forum/read.php?262,359759,376094#msg-376094
I tried disabeling stuff, starting with the E stepper motor. Suddenly it printed again. I connected the stepper and it fails. I started to fiddle with the stepper drivers adjusting the ports, after a while I realized I had no clue of their position so I started all over and put the all to a minimum and increased until all axles moved without missing steps. All drivers ended up at a lower setting than before and the sound from the motors were allot less and not as hard.

Now it prints again! Fingers crossed.]]> ice Printing Mon, 30 Jun 2014 02:53:31 -0400 https://reprap.org/forum/read.php?262,359759,369640#msg-369640 Re: Prusa i3 stopping mid print*video* https://reprap.org/forum/read.php?262,359759,369640#msg-369640
Quote
premek
check temperature of yours stepper motor and stepper driver

He said when the problem occurs the 5 volt rail drops to 3.3 volts. I would say that would almost certainly be the cause of the problem and nothing to do with the stepper driver temperature.]]> TheTechnicalNoob Printing Sat, 14 Jun 2014 04:16:19 -0400 https://reprap.org/forum/read.php?262,359759,369001#msg-369001 Re: Prusa i3 stopping mid print*video* https://reprap.org/forum/read.php?262,359759,369001#msg-369001 premek Printing Thu, 12 Jun 2014 17:24:34 -0400 https://reprap.org/forum/read.php?262,359759,368939#msg-368939 Re: Prusa i3 stopping mid print*video* https://reprap.org/forum/read.php?262,359759,368939#msg-368939 I change orignal usb cable with new, better usb cable, and everything ok again.]]> ngocquynh85 Printing Thu, 12 Jun 2014 15:11:43 -0400 https://reprap.org/forum/read.php?262,359759,368218#msg-368218 Re: Prusa i3 stopping mid print*video* https://reprap.org/forum/read.php?262,359759,368218#msg-368218
I also had an issue where the endstop wire were too close to the motor wires, and with the current going through them, I had some random triggering on the endstops, causing layer shifts (with repetier, idk how marlin handles endstops triggering during prints).
Are you endstops and motor wires set appart?]]> kert45 Printing Wed, 11 Jun 2014 04:21:43 -0400 https://reprap.org/forum/read.php?262,359759,368157#msg-368157 Re: Prusa i3 stopping mid print*video* https://reprap.org/forum/read.php?262,359759,368157#msg-368157 ngocquynh85 Printing Tue, 10 Jun 2014 23:54:36 -0400 https://reprap.org/forum/read.php?262,359759,364969#msg-364969 Re: Prusa i3 stopping mid print*video* https://reprap.org/forum/read.php?262,359759,364969#msg-364969
Quote
chris33
Is your usb cable anywhere near a power cable that can cause it

printing without USB makes the same thing.

The new PSU did not help.

will try disabling steppers and extruder next]]> ice Printing Wed, 04 Jun 2014 07:59:33 -0400 https://reprap.org/forum/read.php?262,359759,362210#msg-362210 Re: Prusa i3 stopping mid print*video* https://reprap.org/forum/read.php?262,359759,362210#msg-362210 chris33 Printing Thu, 29 May 2014 13:58:16 -0400 https://reprap.org/forum/read.php?262,359759,361516#msg-361516 Re: Prusa i3 stopping mid print*video* https://reprap.org/forum/read.php?262,359759,361516#msg-361516
Quote
ShaneH
Is that a psu, or a battery charger? Can't find any specs on it, and some sites are listing these under the category of battery charger(???)

It's a switched power supply 12-30volts, 30A. I just orderd a new 650W computer PSU to se if that helps. I started out with a 500W computer unit capable of 20A and it was running very well for a long time, as my problems showed up I changed to the Switched PSU as a step in finding the issue. But I do not know how good the juice are from this unit.]]> ice Printing Wed, 28 May 2014 08:04:12 -0400 https://reprap.org/forum/read.php?262,359759,361514#msg-361514 Re: Prusa i3 stopping mid print*video* https://reprap.org/forum/read.php?262,359759,361514#msg-361514
Quote
ShaneH
Wow...sounds like it's being powered with a jackhammer! Has it always been that noisy?

And just between you and me....you should really do something with your wiring. You could have a weak joint somewhere in that mess, and when it gets to a certain z height, and the wires pull in a particular way, could be causing your issue. I would run a print and start moving wires. If it cuts out, then a full wiring check would be a great start.

The mess is from trying to find the fault. The sound are not that bad IRL. In normal everything is routed tidy.]]> ice Printing Wed, 28 May 2014 08:01:26 -0400 https://reprap.org/forum/read.php?262,359759,361424#msg-361424 Re: Prusa i3 stopping mid print*video* https://reprap.org/forum/read.php?262,359759,361424#msg-361424
And just between you and me....you should really do something with your wiring. You could have a weak joint somewhere in that mess, and when it gets to a certain z height, and the wires pull in a particular way, could be causing your issue. I would run a print and start moving wires. If it cuts out, then a full wiring check would be a great start.]]> ShaneH Printing Wed, 28 May 2014 04:47:17 -0400 https://reprap.org/forum/read.php?262,359759,361418#msg-361418 Re: Prusa i3 stopping mid print*video* https://reprap.org/forum/read.php?262,359759,361418#msg-361418 ShaneH Printing Wed, 28 May 2014 04:38:32 -0400 https://reprap.org/forum/read.php?262,359759,361362#msg-361362 Re: Prusa i3 stopping mid print*video* https://reprap.org/forum/read.php?262,359759,361362#msg-361362
Printing without the bed gives a little longer print time before it freezes. My power supply of the day is a 1kW 30A capable unit that are not dropping in voltage. it keeps 12.0v at all times. But I don't know if it filters out EMC as good as a computer PSU?! does it matter?


]]> ice Printing Wed, 28 May 2014 01:41:55 -0400 https://reprap.org/forum/read.php?262,359759,361000#msg-361000 Re: Prusa i3 stopping mid print*video* https://reprap.org/forum/read.php?262,359759,361000#msg-361000
Quote
waitaki
Have you tried printing from your laptop rather than via SD card to see if the problem remains?


Same problems usb printing too.]]> ice Printing Tue, 27 May 2014 08:32:54 -0400 https://reprap.org/forum/read.php?262,359759,360946#msg-360946 Re: Prusa i3 stopping mid print*video* https://reprap.org/forum/read.php?262,359759,360946#msg-360946 waitaki Printing Tue, 27 May 2014 07:08:41 -0400 https://reprap.org/forum/read.php?262,359759,360840#msg-360840 Re: Prusa i3 stopping mid print*video* https://reprap.org/forum/read.php?262,359759,360840#msg-360840
Quote
chris33
are you cooling your stepper drivers

Thanks for you kind reply :)

Only the passive cooling, small heat sinks. Have been working for a long while though and I did try with a new ramps with new drivers too.

However I got some ideas from Collin at Makerfarm and we noticed that when I unplugged the USB cable the LCD went blank. So I changed to the new arduino using my old stock ramps. Now the LCD works without USB too and I though it was all ok, but same problem remains.

When the steppers quit the LCD goes blank, the text fades out only the back-light is on. This might be a hint for you guys knowing how the parts work.

I feel 12V to the ramps, does it pass 12V to arduino and arduino makes it own 5v or does the ramps make 5v and pass to arduino?

I noticed the flat resistors controlling nozzle and bed get too hot to touch.

New video too
[www.youtube.com]]]> ice Printing Tue, 27 May 2014 01:22:05 -0400 https://reprap.org/forum/read.php?262,359759,360583#msg-360583 Re: Prusa i3 stopping mid print*video* https://reprap.org/forum/read.php?262,359759,360583#msg-360583 chris33 Printing Mon, 26 May 2014 10:23:23 -0400 https://reprap.org/forum/read.php?262,359759,359759#msg-359759 Prusa i3 stopping mid print*video* https://reprap.org/forum/read.php?262,359759,359759#msg-359759
I need some help. My printer have been working flawless for a long time. Suddenly it started acting strange. Stopping mid print and the steppers did not answer until a reboot of the printer.

I tried:

New arduino
new ramps with new drivers
re flash firmware with auto bed leveling
re flash stock firmware (makerfarm)
disable bed leveling servo
new PSU
re install computer software
new computer fresh install
new USB cable
printing from SD card

all doing the same.


Can a stepper gone bad? they sound and work very fine when I do the pre-print movements but it will only print for a little while then quit. Sometimes a sudden stop or sometimes a sort of down stepping like its buffering more and more moving slower and slower. Sometimes the motors squeal instead of move after I stopped the print. A reboot and they move fine again.

Heaters are "on" but cooling... it seems to think it's still going but it's not :S

see video of example. (Never mind it not extruding at the moment, slipping on the filament)

[www.youtube.com]

Very grateful for help :)]]> ice Printing Sat, 24 May 2014 07:23:03 -0400