Printer-bot prints have some serous Y-axis stepping isus. The included photos show an attempted print of a 30x30x30mm cube. [imgur.com] X-axis seams to be vary reliably strati but the Y-axis seams to progressively wonder, this happened with both slicer and curia. Y-axis driver is set at around 1.47vdc (max of 1.726vdc) I've tried adjusting the driver voltage but it dos-int seam to have to much of an effect on the outcome. I'm currently using Rpetier, slicer or cura. Printer board version is Rev-D Any suggestions or help is greatly appreciated, thanks. https://reprap.org/forum/read.php?262,490246,490246#msg-490246 Thu, 15 Oct 2026 07:42:21 -0400 Phorum 5.2.23 https://reprap.org/forum/read.php?262,490246,490814#msg-490814 https://reprap.org/forum/read.php?262,490246,490814#msg-490814 thanks for all the help]]> NoobyReper Printing Mon, 30 Mar 2015 23:04:57 -0400 https://reprap.org/forum/read.php?262,490246,490804#msg-490804 https://reprap.org/forum/read.php?262,490246,490804#msg-490804
Thanks, I'll update you soon.]]> NoobyReper Printing Mon, 30 Mar 2015 20:47:53 -0400 https://reprap.org/forum/read.php?262,490246,490607#msg-490607 https://reprap.org/forum/read.php?262,490246,490607#msg-490607 It may have been the end stops.]]> KingRahl Printing Mon, 30 Mar 2015 13:03:52 -0400 https://reprap.org/forum/read.php?262,490246,490342#msg-490342 https://reprap.org/forum/read.php?262,490246,490342#msg-490342 NoobyReper Printing Mon, 30 Mar 2015 01:02:04 -0400 https://reprap.org/forum/read.php?262,490246,490330#msg-490330 https://reprap.org/forum/read.php?262,490246,490330#msg-490330 KingRahl Printing Sun, 29 Mar 2015 23:14:48 -0400 https://reprap.org/forum/read.php?262,490246,490313#msg-490313 https://reprap.org/forum/read.php?262,490246,490313#msg-490313 any thoughts?]]> NoobyReper Printing Sun, 29 Mar 2015 21:01:13 -0400 https://reprap.org/forum/read.php?262,490246,490302#msg-490302 https://reprap.org/forum/read.php?262,490246,490302#msg-490302
bin doing more test ant the stepper motor appears to be getting increasingly bad, as it seam to struggle to move the bed even thou it previously had vary little trouble.

going to remove the motor and run further tests.]]> NoobyReper Printing Sun, 29 Mar 2015 19:36:09 -0400 https://reprap.org/forum/read.php?262,490246,490299#msg-490299 https://reprap.org/forum/read.php?262,490246,490299#msg-490299
Since the entire Y-Carriage with smooth rods is balanced on a relatively short base, it may be tilting.
Make sure the bearings are straight and the bearing holders are tightened firm.
There may be an extra tab on a piece of wood keeping a bearing crooked.]]> KingRahl Printing Sun, 29 Mar 2015 19:22:17 -0400 https://reprap.org/forum/read.php?262,490246,490246#msg-490246 https://reprap.org/forum/read.php?262,490246,490246#msg-490246
[imgur.com]

X-axis seams to be vary reliably strati but the Y-axis seams to progressively wonder, this happened with both slicer and curia. Y-axis driver is set at around 1.47vdc (max of 1.726vdc)
I've tried adjusting the driver voltage but it dos-int seam to have to much of an effect on the outcome.

I'm currently using Rpetier, slicer or cura. Printer board version is Rev-D

Any suggestions or help is greatly appreciated, thanks.]]> NoobyReper Printing Sun, 29 Mar 2015 16:24:54 -0400