I wonder if the temp on bed and hot end is posible to set to 0 degres they are know standing on T: 60,2 and B:62,3. If i put the temp to T:230 ist the head then 169,8 or 230. The question is because i dont get any PLA out of the hot end before i set the T:250 degres. https://reprap.org/forum/read.php?262,741826,741826#msg-741826 Fri, 11 Sep 2026 12:41:26 -0400 Phorum 5.2.23 https://reprap.org/forum/read.php?262,741826,741859#msg-741859 https://reprap.org/forum/read.php?262,741826,741859#msg-741859
Thanks.]]> helwic Printing Tue, 24 Jan 2017 15:56:03 -0500 https://reprap.org/forum/read.php?262,741826,741842#msg-741842 https://reprap.org/forum/read.php?262,741826,741842#msg-741842 stephenrc Printing Tue, 24 Jan 2017 14:38:47 -0500 https://reprap.org/forum/read.php?262,741826,741840#msg-741840 https://reprap.org/forum/read.php?262,741826,741840#msg-741840 The config file is under. Im new and just started to calibrate the maskin.


; Configuration file for RepRap Ormerod 2
; RepRapPro Ltd
;
; Copy this file to config.g if you have an Ormerod 2
; If you are updating a config.g that you already have you
; may wish to go through it and this file checking what you
; want to keep from your old file.
;
M111 S0 ; Debug off
M550 PMy RepRapPro Ormerod 2 ; Machine name (can be anything you like)
M551 Preprap ; Machine password (currently not used)
M540 P0xBE:0xEF:0xDE:0xAD:0xFE:0xED ; MAC Address
M552 P192.168.1.14 ; IP address
M553 P255.255.255.0 ; Netmask
M554 P192.168.1.1 ; Gateway
M555 P2 ; Set output to look like Marlin
G21 ; Work in millimetres
G90 ; Send absolute corrdinates...
M83 ; ...but relative extruder moves
M906 X800 Y1000 Z800 E800 ; Set motor currents (mA)
;M305 P0 R4700 ; Set the heated bed thermistor series resistor to 4K7
;M305 P1 R4700 ; Set the hot end thermistor series resistor to 4K7
M569 P0 S0 ; Reverse the X motor
M92 E420 ; Set extruder steps per mm
M558 P2 ; Use a modulated Z probe
G31 Z0.8 P600 ; Set the probe height and threshold (deliberately too high to avoid bed crashes on initial setup)
M557 P0 X45 Y0 ; Four...
M557 P1 X45 Y190 ; ...probe points...
M557 P2 X215 Y190 ; ...for bed...
M557 P3 X215 Y0 ; ...levelling
M556 S78 X0 Y0 Z0 ; Put your axis compensation here
M201 X500 Y500 Z15 E500 ; Accelerations (mm/s^2)
M203 X15000 Y15000 Z100 E3600 ; Maximum speeds (mm/min)
M566 X1200 Y1200 Z30 E1200 ; Minimum speeds mm/minute
M563 P1 D0 H1 ; Define tool 1
G10 P1 S-273 R-273 ; Set tool 1 operating and standby temperatures]]> helwic Printing Tue, 24 Jan 2017 14:28:07 -0500 https://reprap.org/forum/read.php?262,741826,741833#msg-741833 https://reprap.org/forum/read.php?262,741826,741833#msg-741833 obewan Printing Tue, 24 Jan 2017 14:18:18 -0500 https://reprap.org/forum/read.php?262,741826,741826#msg-741826 https://reprap.org/forum/read.php?262,741826,741826#msg-741826 If i put the temp to T:230 ist the head then 169,8 or 230. The question is because i dont get any PLA out of the hot end before i set the T:250 degres.]]> helwic Printing Tue, 24 Jan 2017 14:02:20 -0500