Available for download: [slic3r.org] https://reprap.org/forum/read.php?263,167804,167804#msg-167804 Mon, 07 Sep 2026 08:22:04 -0400 Phorum 5.2.23 https://reprap.org/forum/read.php?263,167804,174070#msg-174070 https://reprap.org/forum/read.php?263,167804,174070#msg-174070 Sound Slic3r Mon, 31 Dec 2012 07:59:39 -0500 https://reprap.org/forum/read.php?263,167804,173247#msg-173247 https://reprap.org/forum/read.php?263,167804,173247#msg-173247 www.thingiverse.com] with horrible results with v0.9.7. Re-slicing it with v0.9.3 results in a much more acceptable gcode. Both versions create these additional travel that drips PLA extrusion on top of solid layers causing a messy print. I hope that can be fixed.


The Bread_Top.stl sliced with the latest version contains multiple bridge layers that should not be there. This may be a major bug in this version that needs an immediate resolution.]]> peddiparth Slic3r Wed, 26 Dec 2012 17:21:49 -0500 https://reprap.org/forum/read.php?263,167804,173039#msg-173039 https://reprap.org/forum/read.php?263,167804,173039#msg-173039 ivymike1031 Slic3r Mon, 24 Dec 2012 18:40:43 -0500 https://reprap.org/forum/read.php?263,167804,172208#msg-172208 https://reprap.org/forum/read.php?263,167804,172208#msg-172208 brnrd Slic3r Wed, 19 Dec 2012 11:33:50 -0500 https://reprap.org/forum/read.php?263,167804,172203#msg-172203 https://reprap.org/forum/read.php?263,167804,172203#msg-172203 -------------------------------------------------------
>
> My production version remains at 0.8.4.
>

Really! that's a very bad release, everything you print using 0.8.4 will be too big, gears will not mesh and holes are the wrong size - that's the worst version to be using.

Step back to 0.8.3 or 0.9.1 for a accurate version.]]> richrap Slic3r Wed, 19 Dec 2012 11:19:42 -0500 https://reprap.org/forum/read.php?263,167804,172099#msg-172099 https://reprap.org/forum/read.php?263,167804,172099#msg-172099
This version seems to be extruding too little on the first layer. I have my first layer the same thickness as the rest and I found that the extruded filament won't stick to the bed and come out at the right width unless I move my endstop closer to the bed so that my first layer is actually about half the thickness as it's supposed to be.

This version also starts the print with a retract. This is actually the wrong move to be making. It should actually start with a feed restart since the previous print should have ended with a retract if it finished properly.

My production version remains at 0.8.4.

Thanks for all your work.]]> brnrd Slic3r Tue, 18 Dec 2012 16:17:16 -0500 https://reprap.org/forum/read.php?263,167804,171664#msg-171664 https://reprap.org/forum/read.php?263,167804,171664#msg-171664 Logrod Slic3r Sat, 15 Dec 2012 18:43:05 -0500 https://reprap.org/forum/read.php?263,167804,171653#msg-171653 https://reprap.org/forum/read.php?263,167804,171653#msg-171653
As far as I can tell all surface finish issues have been fixed in this release. Very nice work!]]> crispy1 Slic3r Sat, 15 Dec 2012 16:35:50 -0500 https://reprap.org/forum/read.php?263,167804,171420#msg-171420 https://reprap.org/forum/read.php?263,167804,171420#msg-171420
The first layer extrusion width(in my case it's 200%) is not calculated over the layer height(0,25),
but over the first layer height(85%).

So I want to get a first layer extrusion width of 0,5mm, instead, I get 0,425mm
Is this correct?]]> Ate Slic3r Fri, 14 Dec 2012 09:51:36 -0500 https://reprap.org/forum/read.php?263,167804,171339#msg-171339 https://reprap.org/forum/read.php?263,167804,171339#msg-171339 doctek Slic3r Thu, 13 Dec 2012 22:41:25 -0500 https://reprap.org/forum/read.php?263,167804,170720#msg-170720 https://reprap.org/forum/read.php?263,167804,170720#msg-170720
c:\Slic3r>slic3r-console --load config.ini filename.stl
this command properly works in 0.7 but same command not working in 0.9.7

Plz Help me.]]> Rajesh Slic3r Tue, 11 Dec 2012 02:16:00 -0500 https://reprap.org/forum/read.php?263,167804,169630#msg-169630 https://reprap.org/forum/read.php?263,167804,169630#msg-169630
Have there been any changes in how circles are handled? Previous versions would interpolate a true circle from the stl, but 0.9.7 creates a polygon.]]> carbo Slic3r Tue, 04 Dec 2012 09:26:28 -0500 https://reprap.org/forum/read.php?263,167804,167943#msg-167943 https://reprap.org/forum/read.php?263,167804,167943#msg-167943
I'm using Repetier v0.80. I've tried creating the gcode by slic3r alone, and doing a cut/paste into repetier, and having repetier do it on it's own with the same results.

./Andrew]]> draeician Slic3r Sat, 24 Nov 2012 18:00:12 -0500 https://reprap.org/forum/read.php?263,167804,167804#msg-167804 https://reprap.org/forum/read.php?263,167804,167804#msg-167804 slic3r.org]]]> Sound Slic3r Fri, 23 Nov 2012 14:15:47 -0500