Hi, Trying some firmwares with my recently burnloaded Gen6, I'm encountering one problem with Repetier. My X and Y endstops are "not detected" while the Z one works perfectly. I can't sort why this behavior, and tried many settings. The 3 endstops are opto endstops, exactly the same, that's why I don't understand why it works for the Z one, and not for the 2 others. X, Y and Z moves are working fine. Heater is ok, just this endstop problem :(. I tried the Sprinter firmware and all is working fine with this one (and Repetier-host). Just a weakness, the heater temperature regulation. Sprinter PID regulation is not as good as Repetier one (or I'm too bad setting it lol...). If it possible to have some orientations in order to fix that, would be cool :). https://reprap.org/forum/read.php?267,186585,186585#msg-186585 Tue, 06 Oct 2026 09:02:27 -0400 Phorum 5.2.23 https://reprap.org/forum/read.php?267,186585,186987#msg-186987 https://reprap.org/forum/read.php?267,186585,186987#msg-186987
With your post and rereading the comment I understand now. I was a bit tired these last nights, sorry...]]> Couby Repetier Sat, 23 Feb 2013 03:50:04 -0500 https://reprap.org/forum/read.php?267,186585,186977#msg-186977 https://reprap.org/forum/read.php?267,186585,186977#msg-186977 repetier Repetier Sat, 23 Feb 2013 02:54:28 -0500 https://reprap.org/forum/read.php?267,186585,186908#msg-186908 https://reprap.org/forum/read.php?267,186585,186908#msg-186908
With #define ALWAYS_CHECK_ENDSTOPS true, X and Y endstops are detected now :).

I'm not sure to understand well the comment about this setting, but the result is there :).


Thank you Repetier :)-D .]]> Couby Repetier Fri, 22 Feb 2013 16:52:13 -0500 https://reprap.org/forum/read.php?267,186585,186855#msg-186855 https://reprap.org/forum/read.php?267,186585,186855#msg-186855
This one ?]]> Couby Repetier Fri, 22 Feb 2013 12:30:52 -0500 https://reprap.org/forum/read.php?267,186585,186851#msg-186851 https://reprap.org/forum/read.php?267,186585,186851#msg-186851 Couby Repetier Fri, 22 Feb 2013 12:18:10 -0500 https://reprap.org/forum/read.php?267,186585,186685#msg-186685 https://reprap.org/forum/read.php?267,186585,186685#msg-186685 repetier Repetier Fri, 22 Feb 2013 03:16:54 -0500 https://reprap.org/forum/read.php?267,186585,186585#msg-186585 https://reprap.org/forum/read.php?267,186585,186585#msg-186585
Trying some firmwares with my recently burnloaded Gen6, I'm encountering one problem with Repetier. My X and Y endstops are "not detected" while the Z one works perfectly. I can't sort why this behavior, and tried many settings. The 3 endstops are opto endstops, exactly the same, that's why I don't understand why it works for the Z one, and not for the 2 others.
X, Y and Z moves are working fine. Heater is ok, just this endstop problem :(.

I tried the Sprinter firmware and all is working fine with this one (and Repetier-host). Just a weakness, the heater temperature regulation. Sprinter PID regulation is not as good as Repetier one (or I'm too bad setting it lol...).

If it possible to have some orientations in order to fix that, would be cool :).]]> Couby Repetier Thu, 21 Feb 2013 15:47:42 -0500