Finally finishing a Mendel90 Hola! Ok, not Spanish, just saying hello :) I bought a kit off a friend some time ago (he had access to a laser cutter and did a few ally cutouts based on the DiBond Mendel90) and I never planned to run it on a ISO threaded bar - always intended to go to a T8x1 ACME and even had the parts to go with it. Roll on to today and after spending some time getting my foldarap back up and running, I'm finally running off new X-Ends that incorporate an anti-backlash T8 ACME nut, and should remain compatible with the rest of the build That leads me to my next question - when I built my Foldarap (6 years ago!) I cut my own Gen 7 (V1.3 or early V1.4 - not sure) board. This is great, I can run Marlin on it, I found my backups and config, and I've got Marlin 2.0 running on it today and it's running very well. I don't mind cutting my own board again, and I'm not really in a rush, so the question is: What's the "best" board out there (firmware supported etc)? I like that I can replace a stepper driver if I want to on the Gen7, and I guess that's something I'd desire in the future. I'm really happy with Marlin, but the world has turned in the past 6 years, and I'm so out of touch I feel like I'm starting again. Thanks for any feedback you can give me https://reprap.org/forum/read.php?292,879193,879193#msg-879193 Mon, 08 Jun 2026 01:52:06 -0400 Phorum 5.2.23 https://reprap.org/forum/read.php?292,879193,880042#msg-880042 Re: Finally finishing a Mendel90 https://reprap.org/forum/read.php?292,879193,880042#msg-880042 www.nerdsmith.co.uk]]]> majic79 Mendel90 Thu, 31 Dec 2020 19:12:53 -0500 https://reprap.org/forum/read.php?292,879193,879218#msg-879218 Re: Finally finishing a Mendel90 https://reprap.org/forum/read.php?292,879193,879218#msg-879218 Roberts_Clif Mendel90 Mon, 30 Nov 2020 16:20:19 -0500 https://reprap.org/forum/read.php?292,879193,879214#msg-879214 Re: Finally finishing a Mendel90 https://reprap.org/forum/read.php?292,879193,879214#msg-879214
Prior to the Pi, I had an old laptop that did the job quite well, but I switch to a Pi only when it was no longer able to upgrade]]> majic79 Mendel90 Mon, 30 Nov 2020 10:05:36 -0500 https://reprap.org/forum/read.php?292,879193,879213#msg-879213 Re: Finally finishing a Mendel90 https://reprap.org/forum/read.php?292,879193,879213#msg-879213
Quote
Traumflug
For finding out the Gen7 version, look at the copper side. Version number should be etched/milled in there.

Yeah, I took your design and replaced a couple of components (used screw terminals instead of the ATX and Molex connectors). I think I ported to KiCad as well and did all my PCB layout there (I've used KiCad longer than I've had a 3D printer, so it was familiar to me at the time) - I don't think I etched that in there when I did the board....]]> majic79 Mendel90 Mon, 30 Nov 2020 10:03:43 -0500 https://reprap.org/forum/read.php?292,879193,879212#msg-879212 Re: Finally finishing a Mendel90 https://reprap.org/forum/read.php?292,879193,879212#msg-879212
Regarding being the latest ... well, these boards still move printers just fine. I run fairly old boards (by today's standards) as well and feel no need to upgrade anything. There's Gen7 2.0 with an ARM CPU, which is about 2.5x faster and Teacup Firmware only. Very helpful when using high resolution stepper drivers and/or spindles to drive axes.

Modern boards certainly lean towards being full-featured computers, running neither Marlin nor Teacup, but a full (Linux) operating system. Then one has direct network (Ethernet, WLAN) access, a proper display and keyboard (or VNC access), can do slicing on the printer, and so on. I'd consider this to be a shift big enough to think about upgrading.]]> Traumflug Mendel90 Mon, 30 Nov 2020 08:43:13 -0500 https://reprap.org/forum/read.php?292,879193,879203#msg-879203 Re: Finally finishing a Mendel90 https://reprap.org/forum/read.php?292,879193,879203#msg-879203
My 3D Printer is similar though does not fold it is a solid T-Slot construction.]]> Roberts_Clif Mendel90 Sun, 29 Nov 2020 19:51:09 -0500 https://reprap.org/forum/read.php?292,879193,879193#msg-879193 Finally finishing a Mendel90 https://reprap.org/forum/read.php?292,879193,879193#msg-879193
Ok, not Spanish, just saying hello :)

I bought a kit off a friend some time ago (he had access to a laser cutter and did a few ally cutouts based on the DiBond Mendel90) and I never planned to run it on a ISO threaded bar - always intended to go to a T8x1 ACME and even had the parts to go with it.

Roll on to today and after spending some time getting my foldarap back up and running, I'm finally running off new X-Ends that incorporate an anti-backlash T8 ACME nut, and should remain compatible with the rest of the build

That leads me to my next question - when I built my Foldarap (6 years ago!) I cut my own Gen 7 (V1.3 or early V1.4 - not sure) board. This is great, I can run Marlin on it, I found my backups and config, and I've got Marlin 2.0 running on it today and it's running very well.

I don't mind cutting my own board again, and I'm not really in a rush, so the question is: What's the "best" board out there (firmware supported etc)? I like that I can replace a stepper driver if I want to on the Gen7, and I guess that's something I'd desire in the future. I'm really happy with Marlin, but the world has turned in the past 6 years, and I'm so out of touch I feel like I'm starting again.

Thanks for any feedback you can give me]]> majic79 Mendel90 Sun, 29 Nov 2020 15:57:36 -0500