Zdar lidi, mám takový problém. Tiskárna manuální povely poslouchá (extrude 5mm, teploty, posuvy ve všech osách (XX) mm i home), ale když nahraju G-code a dám print, tak se ani nepohne. Jediné co, tak pronterface háže hlašky T: (XX) E:0 B: (XX). V čem může být chyba? i3 Arduino+ramps1.4 FW: marlin https://reprap.org/forum/read.php?324,489397,489397#msg-489397 Sun, 16 Aug 2026 03:25:53 -0400 Phorum 5.2.23 https://reprap.org/forum/read.php?324,489397,493147#msg-493147 https://reprap.org/forum/read.php?324,489397,493147#msg-493147 zlygriz Problémy Sun, 05 Apr 2015 13:23:47 -0400 https://reprap.org/forum/read.php?324,489397,491713#msg-491713 https://reprap.org/forum/read.php?324,489397,491713#msg-491713 lubosjerabek Problémy Thu, 02 Apr 2015 04:52:00 -0400 https://reprap.org/forum/read.php?324,489397,491692#msg-491692 https://reprap.org/forum/read.php?324,489397,491692#msg-491692
dej si tam jeste m302 (marlin, jinde si nejsem jistej jak je podporovan) nebo v repetieru zapni dry-run - oboji ti povoli simulaci tisku...
respektive m302 v marlinu povoluje cinnost extruderu bez nahrati hotendu (dobre nemit v extruderu fillament)
dry-run je specialitka repetieru - pusti ti regularni g-cod, ale neaktivuje ohrev a tusim ze ani nepousti motor extruderu - proste jen projede g-cod s pohybem X,Y,Z os]]> raptik Problémy Thu, 02 Apr 2015 03:52:31 -0400 https://reprap.org/forum/read.php?324,489397,491594#msg-491594 https://reprap.org/forum/read.php?324,489397,491594#msg-491594 M107
M190 S60 ; wait for bed temperature to be reached
M104 S205 ; set temperature
G28 ; home all axes
G1 Z5 F5000 ; lift nozzle

M109 S205 ; wait for temperature to be reached
G90 ; use absolute coordinates
G92 E0
M82 ; use absolute distances for extrusion
G1 F1800.000 E-1.00000
G92 E0
G1 Z0.300 F7800.000

-----------------------------------
Aha, už to asi vidím taky :) u M190 stačí zadat S0 nebo je na to jiný příkaz? Nemohu teď vyzkoušet, jsem mimo dosah tiskárny :)]]> zlygriz Problémy Wed, 01 Apr 2015 18:19:49 -0400 https://reprap.org/forum/read.php?324,489397,491240#msg-491240 https://reprap.org/forum/read.php?324,489397,491240#msg-491240 lubosjerabek Problémy Tue, 31 Mar 2015 19:32:01 -0400 https://reprap.org/forum/read.php?324,489397,491211#msg-491211 https://reprap.org/forum/read.php?324,489397,491211#msg-491211 zlygriz Problémy Tue, 31 Mar 2015 17:46:55 -0400 https://reprap.org/forum/read.php?324,489397,489843#msg-489843 https://reprap.org/forum/read.php?324,489397,489843#msg-489843 lubosjerabek Problémy Sat, 28 Mar 2015 15:05:12 -0400 https://reprap.org/forum/read.php?324,489397,489397#msg-489397 https://reprap.org/forum/read.php?324,489397,489397#msg-489397
i3
Arduino+ramps1.4
FW: marlin]]> zlygriz Problémy Fri, 27 Mar 2015 14:51:28 -0400