Dobrý den, už asi týden hledám jak nastavit firmwire marlin motor v pronterface funguje ale když dám tisk dělá to blbosti už si nevím rady :/ Tiskárna: Prusa I3 Firmwire: marlin řídící deska: Megatronics 2.0 motory: 17HS13-0404S extruder: MK8 Osa Z:M5 závitová tyč řemen X,Y: gt2 https://reprap.org/forum/read.php?324,587529,587529#msg-587529 Sat, 05 Sep 2026 07:27:50 -0400 Phorum 5.2.23 https://reprap.org/forum/read.php?324,587529,696486#msg-696486 https://reprap.org/forum/read.php?324,587529,696486#msg-696486 // default settings

#define DEFAULT_AXIS_STEPS_PER_UNIT {80,80,4000,174.2} // default steps per unit for Ultimaker
#define DEFAULT_MAX_FEEDRATE {250, 250, 3.3, 25} // (mm/sec)
#define DEFAULT_MAX_ACCELERATION {3000,3000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot.

#define DEFAULT_ACCELERATION 1000 // X, Y, Z and E max acceleration in mm/s^2 for printing moves
#define DEFAULT_RETRACT_ACCELERATION 1000 // X, Y, Z and E max acceleration in mm/s^2 for retracts]]> vlada Problémy Mon, 08 Aug 2016 08:03:09 -0400 https://reprap.org/forum/read.php?324,587529,589958#msg-589958 https://reprap.org/forum/read.php?324,587529,589958#msg-589958 paycz Problémy Fri, 27 Nov 2015 13:25:52 -0500 https://reprap.org/forum/read.php?324,587529,589048#msg-589048 https://reprap.org/forum/read.php?324,587529,589048#msg-589048 jokejoke Problémy Wed, 25 Nov 2015 15:17:29 -0500 https://reprap.org/forum/read.php?324,587529,588954#msg-588954 https://reprap.org/forum/read.php?324,587529,588954#msg-588954 paycz Problémy Wed, 25 Nov 2015 11:43:12 -0500 https://reprap.org/forum/read.php?324,587529,588598#msg-588598 https://reprap.org/forum/read.php?324,587529,588598#msg-588598 3200/0.8?]]> jokejoke Problémy Tue, 24 Nov 2015 15:59:05 -0500 https://reprap.org/forum/read.php?324,587529,588596#msg-588596 https://reprap.org/forum/read.php?324,587529,588596#msg-588596 hodnotu/8 proud mám dobře
dál jsem "tisk" deseti centimetrové krychle a extruder byl cca 11cm od podložky ostatní osy mám podle [prusaprinters.org]]]> paycz Problémy Tue, 24 Nov 2015 15:56:24 -0500 https://reprap.org/forum/read.php?324,587529,588587#msg-588587 https://reprap.org/forum/read.php?324,587529,588587#msg-588587 4000,174.2} - jestli tedy pri pohybu motor jenom vrci, tak mate nejspis malo proudu do motoru (jestli je dobre zapojeny) - nastavite tim malym trimrem na desticce driveru osy Z. A ty GT2 maji kolik zubu?]]> jokejoke Problémy Tue, 24 Nov 2015 15:48:17 -0500 https://reprap.org/forum/read.php?324,587529,588572#msg-588572 https://reprap.org/forum/read.php?324,587529,588572#msg-588572 motor 17HS13-0404S
driver A4988 od geetech]]> paycz Problémy Tue, 24 Nov 2015 15:37:03 -0500 https://reprap.org/forum/read.php?324,587529,588556#msg-588556 https://reprap.org/forum/read.php?324,587529,588556#msg-588556 jokejoke Problémy Tue, 24 Nov 2015 15:03:32 -0500 https://reprap.org/forum/read.php?324,587529,588552#msg-588552 https://reprap.org/forum/read.php?324,587529,588552#msg-588552 4000/8,174.2} je možné aby to správně krokovalo ?]]> paycz Problémy Tue, 24 Nov 2015 14:52:45 -0500 https://reprap.org/forum/read.php?324,587529,588424#msg-588424 https://reprap.org/forum/read.php?324,587529,588424#msg-588424 paycz Problémy Tue, 24 Nov 2015 11:06:36 -0500 https://reprap.org/forum/read.php?324,587529,588228#msg-588228 https://reprap.org/forum/read.php?324,587529,588228#msg-588228 Home X, Home Y, Home Z, tak zajedou na spinace na osach? Mate mechanicke endstopy a zapojene nozicky NC a C? Jeste koukam, ze to zkousite bez termistoru - nastavte si, kdyz generujete GCODE přes Slic3r teploty na 0C na záložce Filament, aby to necekalo na zacatku tisku na nahrati trysky.]]> jokejoke Problémy Tue, 24 Nov 2015 01:18:11 -0500 https://reprap.org/forum/read.php?324,587529,588035#msg-588035 https://reprap.org/forum/read.php?324,587529,588035#msg-588035 www.dropbox.com]]]> paycz Problémy Mon, 23 Nov 2015 13:12:02 -0500 https://reprap.org/forum/read.php?324,587529,588033#msg-588033 https://reprap.org/forum/read.php?324,587529,588033#msg-588033 v pronterface vše funguje
blbosti znamená že se motor otočí o 0.1 a pak jen vrčí
firmwire:]]> paycz Problémy Mon, 23 Nov 2015 13:09:37 -0500 https://reprap.org/forum/read.php?324,587529,587605#msg-587605 https://reprap.org/forum/read.php?324,587529,587605#msg-587605 jokejoke Problémy Sun, 22 Nov 2015 15:29:17 -0500 https://reprap.org/forum/read.php?324,587529,587529#msg-587529 https://reprap.org/forum/read.php?324,587529,587529#msg-587529 Tiskárna: Prusa I3
Firmwire: marlin
řídící deska: Megatronics 2.0
motory: 17HS13-0404S
extruder: MK8
Osa Z:M5 závitová tyč
řemen X,Y: gt2]]> paycz Problémy Sun, 22 Nov 2015 11:15:52 -0500