Can this bottom curve be improved?

Can this bottom curve be improved? This has always happened and I have put up with it. The top of the curve prints OK but the bottom just doesn't follow the design correctly [attachment 34588 photo1.jpg] [attachment 34589 photo2.jpg] As you can see the bottom curve is almost straight, it should mirror the top curve. I have played around with cooling, hot-end and bed temperatures, slic3r settings and nothing seems to work. I am starting to think that maybe this is a problem with slic3r and not an ormerod problem at all. Any advice and help will be much appreciated. Paul https://reprap.org/forum/read.php?340,367457,367457#msg-367457 Fri, 04 Sep 2026 23:00:13 -0400 Phorum 5.2.23 https://reprap.org/forum/read.php?340,367457,383347#msg-383347 Re: Can this bottom curve be improved? https://reprap.org/forum/read.php?340,367457,383347#msg-383347
The support often makes the print appear to be a complete mess, but it's surprising how easily it can be removed to reveal a good print underneath.

Dave
(#106)]]> dmould Ormerod Tue, 15 Jul 2014 11:45:50 -0400 https://reprap.org/forum/read.php?340,367457,383290#msg-383290 Re: Can this bottom curve be improved? https://reprap.org/forum/read.php?340,367457,383290#msg-383290
I'm interested in printing tubular structures that would have portions forced to be printed horizontally.]]> paradiddle65 Ormerod Tue, 15 Jul 2014 10:01:42 -0400 https://reprap.org/forum/read.php?340,367457,369006#msg-369006 Re: Can this bottom curve be improved? https://reprap.org/forum/read.php?340,367457,369006#msg-369006 Edit: Looked, you've got some bad z-banding. What screw, if any, are you using for Z axis? Steps per mm you have set?]]> MrDoctorDIV Ormerod Thu, 12 Jun 2014 17:33:12 -0400 https://reprap.org/forum/read.php?340,367457,368938#msg-368938 Re: Can this bottom curve be improved? https://reprap.org/forum/read.php?340,367457,368938#msg-368938

Quote
appjaws1
Reverted to the original ormerod fan which produces a much better air flow compared to the quiet fan I was using.

The result is a great improvement on the lower curves, still not correct but much better.

[attachment 34692 test-original-fan.jpg]

Mine happened to be exactly the same result as yours. Looking fir solution for this for a while yet stil
not found any setting that can get it better. Hope there is an answer to this issue soon.]]> Chaisaeng Ormerod Thu, 12 Jun 2014 15:10:36 -0400 https://reprap.org/forum/read.php?340,367457,368844#msg-368844 Re: Can this bottom curve be improved? https://reprap.org/forum/read.php?340,367457,368844#msg-368844 auser Ormerod Thu, 12 Jun 2014 11:16:02 -0400 https://reprap.org/forum/read.php?340,367457,368607#msg-368607 Re: Can this bottom curve be improved? https://reprap.org/forum/read.php?340,367457,368607#msg-368607

Quote
auser
how warm is "warm air" approximately?

About 40 to 45C]]> JMC Ormerod Wed, 11 Jun 2014 23:23:41 -0400 https://reprap.org/forum/read.php?340,367457,368240#msg-368240 Re: Can this bottom curve be improved? https://reprap.org/forum/read.php?340,367457,368240#msg-368240 auser Ormerod Wed, 11 Jun 2014 05:48:08 -0400 https://reprap.org/forum/read.php?340,367457,368208#msg-368208 Re: Can this bottom curve be improved? https://reprap.org/forum/read.php?340,367457,368208#msg-368208
[attachment 34710 WP_000532.jpg]

I cut the ends off to get better pictures (the center holes are all round tho they dont look it in the pic).

This is the cooling rig i used that blows air on to all sides of the print.

[attachment 34712 WP_000466.jpg]

I have modifide it since this to create more of a whirlwind affect and to allow for hot air to be used.]]> JMC Ormerod Wed, 11 Jun 2014 03:55:08 -0400 https://reprap.org/forum/read.php?340,367457,368016#msg-368016 Re: Can this bottom curve be improved? https://reprap.org/forum/read.php?340,367457,368016#msg-368016
The result is a great improvement on the lower curves, still not correct but much better.

[attachment 34692 test-original-fan.jpg]]]> appjaws1 Ormerod Tue, 10 Jun 2014 15:55:49 -0400 https://reprap.org/forum/read.php?340,367457,367968#msg-367968 Re: Can this bottom curve be improved? https://reprap.org/forum/read.php?340,367457,367968#msg-367968

Quote
JMC
Its a bit hard to take a good pictur

[attachment 34675 WP_000483.jpg]

The upper and lower sides of the curve are not completly symmetrical but there close. Have printed several tests with diffrent amounts cooling but its 2 am and i have to work in the morning so will post them tomorro.

From what I can see the result looks good, better than mine.

Unfortunately I'm not around for the next few weeks but will be very interested in anything you come up with to improve the curves.

Paul]]> appjaws1 Ormerod Tue, 10 Jun 2014 14:40:03 -0400 https://reprap.org/forum/read.php?340,367457,367958#msg-367958 Re: Can this bottom curve be improved? https://reprap.org/forum/read.php?340,367457,367958#msg-367958
[attachment 34675 WP_000483.jpg]

The upper and lower sides of the curve are not completly symmetrical but there close. Have printed several tests with diffrent amounts cooling but its 2 am and i have to work in the morning so will post them tomorro.]]> JMC Ormerod Tue, 10 Jun 2014 14:25:35 -0400 https://reprap.org/forum/read.php?340,367457,367877#msg-367877 Re: Can this bottom curve be improved? https://reprap.org/forum/read.php?340,367457,367877#msg-367877

Quote
appjaws1

Quote
dmould
One other thing to try is to reduce the layer height. That will result in less overhang distance per layer. Also make sure you uncheck the Slic3r option "Print external perimeters first" (Last option in "Print Settings/Layers and perimeters"). If the inner perimeter is printed first, it provides some sort of side support for the outer perimeter even if the outer perimeter is unsupported underneath.

Dave
(#106)

Havent updated in a while so am using an older version. Is a bit academic at the moment sins i have busted somthing so can not print now any way. But from your pictur it looks like a problem i had when i was using a large external fan for print cooling and was only colling from one direction. if i watched closely while printing i could see the very edge warping a little whitch tended to make the underside of curves more of a diagonal. To fix this i got a very powerful little blower fan and ducted the air so the print was cooled from 4 sides in a kind of spiral fashion. Another mod that seemes to help stop edges curling is to use warme air to cool the print this way you can blow more air across the print without cooling doun the hot bed. My previos rig had the air blowing on to the print at about 45C. will print your test shape as soon as i find out what is shorting out my power supply :S]]> JMC Ormerod Tue, 10 Jun 2014 12:38:18 -0400 https://reprap.org/forum/read.php?340,367457,367802#msg-367802 Re: Can this bottom curve be improved? https://reprap.org/forum/read.php?340,367457,367802#msg-367802

Quote
dmould
One other thing to try is to reduce the layer height. That will result in less overhang distance per layer. Also make sure you uncheck the Slic3r option "Print external perimeters first" (Last option in "Print Settings/Layers and perimeters"). If the inner perimeter is printed first, it provides some sort of side support for the outer perimeter even if the outer perimeter is unsupported underneath.

Dave
(#106)

Dave,
I completed a print with layer height of .1 and the problem is exactly the same, see photo. I also have the settings that you suggest.

[attachment 34638 point-one-layer-height-test.jpg]

Pointy - Thank you for your settings, they are very close to mine, the only difference is the speed of some items.

JMC - I think we have all used slic3r to slice the test stl.. What version are you using?
I have reverted to using 1.1.3, as 1.1.4 had problems. Does the part show in slic3r's viewer?

Paul]]> appjaws1 Ormerod Tue, 10 Jun 2014 09:54:57 -0400 https://reprap.org/forum/read.php?340,367457,367801#msg-367801 Re: Can this bottom curve be improved? https://reprap.org/forum/read.php?340,367457,367801#msg-367801 Reducing the layer thickness would help.
When I print stuff like that I put in my own snapable supports. The Big Blue has allot of thin support walls under it to hold it up while printing, that are thin enough to snap out with your fingers afterwards.
I wouldn't use Slic3rs support structures on anything, as I find they are terrible.
To support those downward curves I would place a very thin wall at each edge, so the print head could Bridge between them as the curve builds up.
Add them to your design, then you know where the supports are, and that they won't interfere with your design, and you can make them easy to remove. If Slic3r does it, then it'll be a mess...
I wouldn't use external fans either, as your picture shows signs of Warping, and they will just make it worse.

With the Big Blue, the second fan on my duct is under Slic3r control, and it does a pretty good job at warm areas with a Bulk of plastic, by blowing extra air through the ducts.
The temps I run with are 195' and 57'

It would be interesting to see your machine run the Bridging test... With and without the external fans.]]> KimBrown Ormerod Tue, 10 Jun 2014 09:46:31 -0400 https://reprap.org/forum/read.php?340,367457,367778#msg-367778 Re: Can this bottom curve be improved? https://reprap.org/forum/read.php?340,367457,367778#msg-367778 JMC Ormerod Tue, 10 Jun 2014 08:21:20 -0400 https://reprap.org/forum/read.php?340,367457,367774#msg-367774 Re: Can this bottom curve be improved? https://reprap.org/forum/read.php?340,367457,367774#msg-367774

Quote
appjaws1
Les,
Can I have a copy of your settings to try please.
Looking at your picture, he ones I have printed today are as good, but it would be interesting to compare settings
I have dropped the temperature by 2 degrees and I think that has made the difference, an improvement over yesterdays.
I have printed 1 rotated 90 degrees - an improvement but still a straight line.
Also printed with support selected in slic3r but I can not see any support on the print, again a straight line.

Not ever having used support what should the settings be?

Paul

I have attached my Slic3r settings. I have never used support either so can't help with that.

Regards,

Les]]> Pointy Ormerod Tue, 10 Jun 2014 08:16:28 -0400 https://reprap.org/forum/read.php?340,367457,367761#msg-367761 Re: Can this bottom curve be improved? https://reprap.org/forum/read.php?340,367457,367761#msg-367761 distance per layer. Also make sure you uncheck the Slic3r option "Print external perimeters first" (Last option in "Print Settings/Layers and perimeters"). If the inner perimeter is printed first, it provides some sort of side support for the outer perimeter even if the outer perimeter is unsupported underneath.

Dave
(#106)]]> dmould Ormerod Tue, 10 Jun 2014 07:50:30 -0400 https://reprap.org/forum/read.php?340,367457,367755#msg-367755 Re: Can this bottom curve be improved? https://reprap.org/forum/read.php?340,367457,367755#msg-367755 Can I have a copy of your settings to try please.
Looking at your picture, he ones I have printed today are as good, but it would be interesting to compare settings
I have dropped the temperature by 2 degrees and I think that has made the difference, an improvement over yesterdays.
I have printed 1 rotated 90 degrees - an improvement but still a straight line.
Also printed with support selected in slic3r but I can not see any support on the print, again a straight line.

Not ever having used support what should the settings be?

Paul]]> appjaws1 Ormerod Tue, 10 Jun 2014 07:38:47 -0400 https://reprap.org/forum/read.php?340,367457,367753#msg-367753 Re: Can this bottom curve be improved? https://reprap.org/forum/read.php?340,367457,367753#msg-367753 dc42 Ormerod Tue, 10 Jun 2014 07:31:46 -0400 https://reprap.org/forum/read.php?340,367457,367747#msg-367747 Re: Can this bottom curve be improved? https://reprap.org/forum/read.php?340,367457,367747#msg-367747
[attachment 34632 test.jpg]

Sorry, it's not the best picture, but it didn't come out too bad. It's definitely not as round on the bottom, but it's not as bad as yours. I also didn't rotate it, so it was printed the same direction as in your photo.

Regards,

Les]]> Pointy Ormerod Tue, 10 Jun 2014 07:07:22 -0400 https://reprap.org/forum/read.php?340,367457,367731#msg-367731 Re: Can this bottom curve be improved? https://reprap.org/forum/read.php?340,367457,367731#msg-367731
[attachment 34631 curve-test.png]]]> appjaws1 Ormerod Tue, 10 Jun 2014 06:09:22 -0400 https://reprap.org/forum/read.php?340,367457,367711#msg-367711 Re: Can this bottom curve be improved? https://reprap.org/forum/read.php?340,367457,367711#msg-367711

Quote
Pointy

Try rotating your piece 90 degrees so that the curves face the fan duct and also lower your hotend temps, your print looks stringy which is a sign of too much heat. I use 190 for first layer and the 185 for the rest.

The other interesting thing is that we both use a very similar fan duct...

Maybe we can make a test piece that others can print to verify the problem. Whatis the dimensions of the piece with the curve?

Les

Les,
I will try turning the item through 90 degrees and see if that helps..

My fan duct has 3 outputs, centre directed at the nozzle and the 2 outside directed forward and downwards. I'm going to try the original fan again because I think I need more airflow.

The end of the item is a U shape 10mm tall, 23x21mm with 4mm thick walls and a radius of 5mm on the ends

We should do some tests.

I'll try later but I only have today to work on this.

Thank you for your interest
Paul]]> appjaws1 Ormerod Tue, 10 Jun 2014 04:50:16 -0400 https://reprap.org/forum/read.php?340,367457,367689#msg-367689 Re: Can this bottom curve be improved? https://reprap.org/forum/read.php?340,367457,367689#msg-367689
For what it's worth I have always struggled printing upwards slopes or curves. The original Z Nut Trap piece is a good example of this and I had to print it several times to get a good one. I think it's a cooling issue as I seemed to get better results when the slope is facing the fan duct. I noticed that the upward slope would always curl upwards which meant it went lumpy and would make the nozzle jump.

Try rotating your piece 90 degrees so that the curves face the fan duct and also lower your hotend temps, your print looks stringy which is a sign of too much heat. I use 190 for first layer and the 185 for the rest.

The other interesting thing is that we both use a very similar fan duct...

[attachment 34625 fanduct.png]

Maybe we can make a test piece that others can print to verify the problem. Whatis the dimensions of the piece with the curve?

Regards,

Les]]> Pointy Ormerod Tue, 10 Jun 2014 03:11:37 -0400 https://reprap.org/forum/read.php?340,367457,367588#msg-367588 Re: Can this bottom curve be improved? https://reprap.org/forum/read.php?340,367457,367588#msg-367588
I'm not sure what you mean, the bottom right is just a straight 90 degree angle, the two uprights are finished off with a nice curve above the screw holes.]]> appjaws1 Ormerod Mon, 09 Jun 2014 17:04:39 -0400 https://reprap.org/forum/read.php?340,367457,367585#msg-367585 Re: Can this bottom curve be improved? https://reprap.org/forum/read.php?340,367457,367585#msg-367585 So a curve like the one you show there would start with a 45 degree, then curve nicely towards the top.
Occasionally I'll have to use support mainly because I can't think of any way of sticking to the 45 degree rule, but I prefer not using it as it requires removal which can be difficult and leave traces.

I'm also intrigued by the near bottom right hand side of the model you're printing - what is happening there?]]> VortyZA Ormerod Mon, 09 Jun 2014 16:55:25 -0400 https://reprap.org/forum/read.php?340,367457,367555#msg-367555 Re: Can this bottom curve be improved? https://reprap.org/forum/read.php?340,367457,367555#msg-367555
I have the extrude temperature set at 194 after the fist layer. I also have secondary cooling fans.

I have never used support, it just didn't occur to me that that could help, perhaps I'll try it in the morning.]]> appjaws1 Ormerod Mon, 09 Jun 2014 15:43:32 -0400 https://reprap.org/forum/read.php?340,367457,367516#msg-367516 Re: Can this bottom curve be improved? https://reprap.org/forum/read.php?340,367457,367516#msg-367516 VortyZA Ormerod Mon, 09 Jun 2014 14:12:44 -0400 https://reprap.org/forum/read.php?340,367457,367457#msg-367457 Can this bottom curve be improved? https://reprap.org/forum/read.php?340,367457,367457#msg-367457
[attachment 34588 photo1.jpg]

[attachment 34589 photo2.jpg]

As you can see the bottom curve is almost straight, it should mirror the top curve.
I have played around with cooling, hot-end and bed temperatures, slic3r settings and nothing seems to work.
I am starting to think that maybe this is a problem with slic3r and not an ormerod problem at all.

Any advice and help will be much appreciated.
Paul]]> appjaws1 Ormerod Mon, 09 Jun 2014 11:38:38 -0400