hello, I'm currently trying to assemble a hotend. I tried to follow this list of instructions: [wiki.openhardware.co.za] The resistor does not fit into the head at all. It's way too small. The inner diameter of the head is about 6.1mm and the outer diameter of the resistor is only 5mm. How do I fix that? The how-to mentions wrapping with kitchen foil, but wrapping kitchen foil tight enough seems to be difficult if not impossible. --- I attached a picture of the parts for the hotend (not including the pfte tubing) What is this small screw for? (the small black one, with an inner hex) I _guess_ that it holds the tubing in the head. Could somebody please clarify how this should be assembled or link to a more thorough instruction? thanks https://reprap.org/forum/read.php?4,300579,300579#msg-300579 Sat, 10 Oct 2026 04:16:37 -0400 Phorum 5.2.23 https://reprap.org/forum/read.php?4,300579,303349#msg-303349 https://reprap.org/forum/read.php?4,300579,303349#msg-303349 jameghino Reprappers Thu, 30 Jan 2014 09:53:49 -0500 https://reprap.org/forum/read.php?4,300579,300874#msg-300874 https://reprap.org/forum/read.php?4,300579,300874#msg-300874 The resistors supplied with it are 6mm diam. It is cheaper just to buy the right sized resistor I think.

Screw the brass nozzle all the way into the peek bit, tighten it (without overdoing it), push the ptfe tube all the way down to the bottom, screw the hex screw in and tighten it down. Finally there is a short piece of ptfe tube to fit into the inside of the hex screw, or at least there was on my 1.75mm version. There may not be on a 3mm version.]]> dave3d Reprappers Sat, 25 Jan 2014 13:05:51 -0500 https://reprap.org/forum/read.php?4,300579,300775#msg-300775 https://reprap.org/forum/read.php?4,300579,300775#msg-300775
Had the same problem. I purchased a tube of exhaust repair paste (Holts firegum) from a local car parts shop (actual one of may in a chain of franchise stores in NL). The paste is advertised to resist up to 1000 degrees.

Put some paste on the resistor, popped it in. Then turned up the heat, the paste expanded, solidified and glued the whole thing in place.
Worked perfectly, did the same for thermistor.
Afterwards, I scraped the excess hardened paste from the outside of the heaterblock (just to make it look nice)

Downside, the paste costs 10 euro for a whole tube, I needed only 1 drop.]]> Eric64124 Reprappers Sat, 25 Jan 2014 09:21:47 -0500 https://reprap.org/forum/read.php?4,300579,300594#msg-300594 https://reprap.org/forum/read.php?4,300579,300594#msg-300594
possible solutions is that they sent you the wrong resistor? i got mine from makerfarm and the resistor i got from them fit just right]]> jasperash Reprappers Fri, 24 Jan 2014 19:55:26 -0500 https://reprap.org/forum/read.php?4,300579,300592#msg-300592 https://reprap.org/forum/read.php?4,300579,300592#msg-300592 sheck626 Reprappers Fri, 24 Jan 2014 19:45:17 -0500 https://reprap.org/forum/read.php?4,300579,300579#msg-300579 https://reprap.org/forum/read.php?4,300579,300579#msg-300579
I'm currently trying to assemble a hotend.
I tried to follow this list of instructions:
[wiki.openhardware.co.za]

The resistor does not fit into the head at all. It's way too small.
The inner diameter of the head is about 6.1mm and the outer diameter of the resistor is only 5mm.

How do I fix that? The how-to mentions wrapping with kitchen foil, but wrapping kitchen foil tight enough seems to be difficult if not impossible.

---

I attached a picture of the parts for the hotend (not including the pfte tubing)
What is this small screw for? (the small black one, with an inner hex)
I _guess_ that it holds the tubing in the head.
Could somebody please clarify how this should be assembled or link to a more thorough instruction?

thanks]]> m Reprappers Fri, 24 Jan 2014 19:04:51 -0500