X & Y axis homes in wrong direction Hi, I have a 3D printer with config as follows: ATMEGA2560, RAMPS1.4, Marlin v1 All axis homed correctly until I changed the RAMPS1.4 with a newer one. Now the X & Y axis does not homes correctly. When I press + in X dir then it moves correctly but for homing in X dir it moves in + dir only & that too for 10mm distance....Same is the case for Y axis. I have not changed anything in firmware, I used it as it was for my previous RAMPS board... Anyone faced such situation???? Regards, PRashant. https://reprap.org/forum/read.php?4,433997,433997#msg-433997 Wed, 16 Sep 2026 20:47:02 -0400 Phorum 5.2.23 https://reprap.org/forum/read.php?4,433997,451983#msg-451983 Re: X & Y axis homes in wrong direction[closed] https://reprap.org/forum/read.php?4,433997,451983#msg-451983 Problem solved.. so closed.]]> prashantdshinde Reprappers Wed, 07 Jan 2015 05:59:17 -0500 https://reprap.org/forum/read.php?4,433997,436037#msg-436037 Re: X & Y axis homes in wrong direction - Topic resolved & closed https://reprap.org/forum/read.php?4,433997,436037#msg-436037
The endstop connections were wrong & some settings in marlin were also altered.

Thanks all.]]> prashantdshinde Reprappers Mon, 24 Nov 2014 05:54:33 -0500 https://reprap.org/forum/read.php?4,433997,434185#msg-434185 Re: X & Y axis homes in wrong direction https://reprap.org/forum/read.php?4,433997,434185#msg-434185 svalsorim Reprappers Wed, 19 Nov 2014 10:31:51 -0500 https://reprap.org/forum/read.php?4,433997,434006#msg-434006 Re: X & Y axis homes in wrong direction https://reprap.org/forum/read.php?4,433997,434006#msg-434006 I have the same settings... still getting same issue...]]> prashantdshinde Reprappers Wed, 19 Nov 2014 01:58:40 -0500 https://reprap.org/forum/read.php?4,433997,434001#msg-434001 Re: X & Y axis homes in wrong direction https://reprap.org/forum/read.php?4,433997,434001#msg-434001
// ENDSTOP SETTINGS:
// Sets direction of endstops when homing; 1=MAX, -1=MIN
#define X_HOME_DIR -1
#define Y_HOME_DIR -1
#define Z_HOME_DIR -1]]> svalsorim Reprappers Wed, 19 Nov 2014 01:39:19 -0500 https://reprap.org/forum/read.php?4,433997,433997#msg-433997 X & Y axis homes in wrong direction https://reprap.org/forum/read.php?4,433997,433997#msg-433997 I have a 3D printer with config as follows:

ATMEGA2560,
RAMPS1.4,
Marlin v1

All axis homed correctly until I changed the RAMPS1.4 with a newer one.

Now the X & Y axis does not homes correctly. When I press + in X dir then it moves correctly but for homing in X dir it moves in + dir only & that too for 10mm distance....Same is the case for Y axis.

I have not changed anything in firmware, I used it as it was for my previous RAMPS board...

Anyone faced such situation????

Regards,
PRashant.]]> prashantdshinde Reprappers Wed, 19 Nov 2014 01:21:57 -0500