Tried the BOM generator and mouser import today, its quite impressing. First I tried the comm controller card, no problem. Next it was the stepper motor controller... Found this component to be obsoleted, never done mouser before so I couldn't quite figure out what to do, maybe there is a susbstitute item? I can otherwise be quite creative when substituting connectors when I want to :-E 538-39880-0102 (buy) 2 pin .200" connector The link led me to this page on Molex.com, I don't even recognize this bugger, what is it? [www.molex.com] https://reprap.org/forum/read.php?4,4626,4626#msg-4626 Fri, 11 Sep 2026 12:29:42 -0400 Phorum 5.2.23 https://reprap.org/forum/read.php?4,4626,4960#msg-4960 https://reprap.org/forum/read.php?4,4626,4960#msg-4960 ZachHoeken Reprappers Tue, 11 Sep 2007 15:42:34 -0400 https://reprap.org/forum/read.php?4,4626,4959#msg-4959 https://reprap.org/forum/read.php?4,4626,4959#msg-4959 rmadams Reprappers Tue, 11 Sep 2007 14:01:01 -0400 https://reprap.org/forum/read.php?4,4626,4958#msg-4958 https://reprap.org/forum/read.php?4,4626,4958#msg-4958
i've re-imported the cuttent data for the development site just in case others are using it (bad idea...)]]> ZachHoeken Reprappers Tue, 11 Sep 2007 00:43:16 -0400 https://reprap.org/forum/read.php?4,4626,4956#msg-4956 https://reprap.org/forum/read.php?4,4626,4956#msg-4956 rmadams Reprappers Mon, 10 Sep 2007 23:09:25 -0400 https://reprap.org/forum/read.php?4,4626,4949#msg-4949 https://reprap.org/forum/read.php?4,4626,4949#msg-4949
there is only one entry for each unique part, and then the lists for the collections of parts point to them.

here is the page for the 2 pin .200" connector: [parts.reprap.org]

its showing the correct, new number. make sure you're on parts.reprap.org. also, try shift + reload on the page as well.

~Zach]]> ZachHoeken Reprappers Mon, 10 Sep 2007 18:23:33 -0400 https://reprap.org/forum/read.php?4,4626,4931#msg-4931 https://reprap.org/forum/read.php?4,4626,4931#msg-4931
538-39880-0102 (buy) 2 pin .200" connector

from the BOM entry for the Universal Controller v1.2. Does the system recognize the same part regardless of which board it is in? If not, it might be nice to treat those subsitutions automagically, so that when a change is made on one board, it can propogate through the system.]]> rmadams Reprappers Sun, 09 Sep 2007 19:08:25 -0400 https://reprap.org/forum/read.php?4,4626,4629#msg-4629 https://reprap.org/forum/read.php?4,4626,4629#msg-4629 mimarob Reprappers Tue, 28 Aug 2007 15:50:51 -0400 https://reprap.org/forum/read.php?4,4626,4627#msg-4627 https://reprap.org/forum/read.php?4,4626,4627#msg-4627
[www.mouser.com]

also, the BOM generator has been updated.

thanks for the heads up!]]> ZachHoeken Reprappers Tue, 28 Aug 2007 15:00:50 -0400 https://reprap.org/forum/read.php?4,4626,4626#msg-4626 https://reprap.org/forum/read.php?4,4626,4626#msg-4626
First I tried the comm controller card, no problem.

Next it was the stepper motor controller...

Found this component to be obsoleted, never done mouser before so I couldn't quite figure out what to do, maybe there is a susbstitute item?

I can otherwise be quite creative when substituting connectors when I want to :-E

538-39880-0102 (buy) 2 pin .200" connector

The link led me to this page on Molex.com, I don't even recognize this bugger,
what is it?

[www.molex.com]]]> mimarob Reprappers Tue, 28 Aug 2007 14:21:43 -0400