E3D Lite Just wondering if any one has used the new E3D lite? Im tempted to get a couple for my dual extrude upgrade, the only thing that is putting me off is the given maximum extrusions on the E3D website. Apparently it is only capable of upto 50mm/sec, whereas the normal is 100mm/sec. I know with my print settings I can achieve a flow rate of around 10mm3/sec extruding in mid air with a normal E3D V6, so with the lite am i only going to be able to get 5mm3/sec? Has anyone done any back to back comparisons and noticed a drop in extrusion speeds? As far as I can see the heater block and nozzles are identical so I don't understand why the flow rate would be any slower. Also im intrigued to know how E3D calculate the max print speeds as its highly dependent on layer height. Id much rather they gave flow rates rather than print speed as this is almost independent of layer height. https://reprap.org/forum/read.php?4,611590,611590#msg-611590 Tue, 16 Jun 2026 08:35:30 -0400 Phorum 5.2.23 https://reprap.org/forum/read.php?4,611590,611913#msg-611913 Re: E3D Lite https://reprap.org/forum/read.php?4,611590,611913#msg-611913 Giantkiller Reprappers Mon, 18 Jan 2016 17:30:17 -0500 https://reprap.org/forum/read.php?4,611590,611882#msg-611882 Re: E3D Lite https://reprap.org/forum/read.php?4,611590,611882#msg-611882 gmckee Reprappers Mon, 18 Jan 2016 16:44:55 -0500 https://reprap.org/forum/read.php?4,611590,611741#msg-611741 Re: E3D Lite https://reprap.org/forum/read.php?4,611590,611741#msg-611741
Quote
Giantkiller
Thanks! Snabotutely fenominal!
I am going this route because I have not been able to print any thingies, only test prints which aren't good yet.
I'll just upload to Tinkercad and order a print! Fantastico! The price will probably kill me tho. Let's see.
I will report back here the status.

Where in the world are you?]]> dougal1957 Reprappers Mon, 18 Jan 2016 13:19:48 -0500 https://reprap.org/forum/read.php?4,611590,611732#msg-611732 Re: E3D Lite https://reprap.org/forum/read.php?4,611590,611732#msg-611732 I am going this route because I have not been able to print any thingies, only test prints which aren't good yet.
I'll just upload to Tinkercad and order a print! Fantastico! The price will probably kill me tho. Let's see.
I will report back here the status.]]> Giantkiller Reprappers Mon, 18 Jan 2016 13:03:58 -0500 https://reprap.org/forum/read.php?4,611590,611727#msg-611727 Re: E3D Lite https://reprap.org/forum/read.php?4,611590,611727#msg-611727
Quote
Giantkiller
I am looking to make one that allows the two heads to moving vertically independently. This save having to level the heads at the nozzle end.
But right now I need a single end head mount.

OK If you have the I3 Rework which I am sure you have then how about E3D Carrier for I3 looking at the Replikeo Pictures it looks like it will do what you want.

HTH

Doug]]> dougal1957 Reprappers Mon, 18 Jan 2016 12:48:21 -0500 https://reprap.org/forum/read.php?4,611590,611704#msg-611704 Re: E3D Lite https://reprap.org/forum/read.php?4,611590,611704#msg-611704 But right now I need a single end head mount.]]> Giantkiller Reprappers Mon, 18 Jan 2016 11:52:13 -0500 https://reprap.org/forum/read.php?4,611590,611692#msg-611692 Re: E3D Lite https://reprap.org/forum/read.php?4,611590,611692#msg-611692
Quote
Giantkiller
Are you getting Bowden tube feed or Wade direct feed. If Bowden, where did you get your single or dual head mount. I am looking to go dual myself as my Replikeo came that way but I have to replace the lousy extrusion assemblies.

Be aware that all the E3D Hotends are Bowden (you just fit the little black clamp ring in place) the difference in the shop is that the Bowden Version comes with a good push fit adaptor for the Cold End.

If you want to do Dual extrusion easily then get the E3D Chimera Dual Hotend E3D Chimera]]> dougal1957 Reprappers Mon, 18 Jan 2016 11:33:12 -0500 https://reprap.org/forum/read.php?4,611590,611664#msg-611664 Re: E3D Lite https://reprap.org/forum/read.php?4,611590,611664#msg-611664 Giantkiller Reprappers Mon, 18 Jan 2016 10:39:35 -0500 https://reprap.org/forum/read.php?4,611590,611590#msg-611590 E3D Lite https://reprap.org/forum/read.php?4,611590,611590#msg-611590
Im tempted to get a couple for my dual extrude upgrade, the only thing that is putting me off is the given maximum extrusions on the E3D website. Apparently it is only capable of upto 50mm/sec, whereas the normal is 100mm/sec.
I know with my print settings I can achieve a flow rate of around 10mm3/sec extruding in mid air with a normal E3D V6, so with the lite am i only going to be able to get 5mm3/sec?

Has anyone done any back to back comparisons and noticed a drop in extrusion speeds? As far as I can see the heater block and nozzles are identical so I don't understand why the flow rate would be any slower.

Also im intrigued to know how E3D calculate the max print speeds as its highly dependent on layer height. Id much rather they gave flow rates rather than print speed as this is almost independent of layer height.]]> Andy1989 Reprappers Mon, 18 Jan 2016 08:01:34 -0500