Issues upgrading delta printer from Ramps Plus2 board to Einsy Retro1.0a I have a Flsun Kossel Delta printer that I'm trying to upgrade the motherboard on. It came with a Ramps Plus2 board. I got an Einsy Retro 1.0a board at a Lulzbot garage sale, so I wanted to put it into the Delta. I got everything rewired, plugged in, changed the board and driver types in marlin, turned it on, and not much happened. The fans start to run, but the LCD doesn't turn on and remains unresponsive. The amber light on the board flashes when I turn the knob, so it's reacting somehow. I'm really not sure of where to go from here. Does anyone have any ideas? https://reprap.org/forum/read.php?4,858052,858052#msg-858052 Mon, 05 Oct 2026 22:29:46 -0400 Phorum 5.2.23 https://reprap.org/forum/read.php?4,858052,858058#msg-858058 Re: Issues upgrading delta printer from Ramps Plus2 board to Einsy Retro1.0a https://reprap.org/forum/read.php?4,858052,858058#msg-858058
Without these the lcd will not work.

see [reprap.org]

You then must select Rambo and your board type in the arduino IDE and compile like normal.]]> Dust Reprappers Thu, 15 Aug 2019 03:28:31 -0400 https://reprap.org/forum/read.php?4,858052,858056#msg-858056 Re: Issues upgrading delta printer from Ramps Plus2 board to Einsy Retro1.0a https://reprap.org/forum/read.php?4,858052,858056#msg-858056
Quote
Dust
This page for the Plus2 [img.alicdn.com] shows the gnd and +5v on pins 9 and 10
where as this page for the Einsy retro [github.com] shows power is on pins 1 and 2

Good call. I cut off the tabs on the plugs so I could flip them around and at least it has power now, but no display. Looking at those schematics, it also looks like the TX and RX pins are in different spots too. Is that something that can be fixed in marlin? If not it'd probably easier to order a new LCD that's more compatible.]]> Raxius Reprappers Thu, 15 Aug 2019 03:15:10 -0400 https://reprap.org/forum/read.php?4,858052,858053#msg-858053 Re: Issues upgrading delta printer from Ramps Plus2 board to Einsy Retro1.0a https://reprap.org/forum/read.php?4,858052,858053#msg-858053
Its looks like this is the case here

This page for the Plus2 [img.alicdn.com] shows the gnd and +5v on pins 9 and 10
where as this page for the Einsy retro [github.com] shows power is on pins 1 and 2]]> Dust Reprappers Thu, 15 Aug 2019 02:35:01 -0400 https://reprap.org/forum/read.php?4,858052,858052#msg-858052 Issues upgrading delta printer from Ramps Plus2 board to Einsy Retro1.0a https://reprap.org/forum/read.php?4,858052,858052#msg-858052 It came with a Ramps Plus2 board.
I got an Einsy Retro 1.0a board at a Lulzbot garage sale, so I wanted to put it into the Delta.

I got everything rewired, plugged in, changed the board and driver types in marlin, turned it on, and not much happened.
The fans start to run, but the LCD doesn't turn on and remains unresponsive.
The amber light on the board flashes when I turn the knob, so it's reacting somehow.

I'm really not sure of where to go from here. Does anyone have any ideas?]]> Raxius Reprappers Thu, 15 Aug 2019 01:26:47 -0400