Has anyone tried or has been able to upload firmware on this chip using a sanguino board using arduino version 0023 as interface . . I have been able to compile and upload firmware on sanguino with atmega 644p and with ramps 1.3 using arduino 2560 and arduino1280 boards . . . I went on and practiced my google-fu on the subject chip and followed all the insttuctions but still cant seem to uplpad firmware on it . . .i get a programmer not responding error . .so got me thinking it might be the bootloader . .good practice though for better understanding how the arduino interface works . . . how can i verify my installed bootloader on the chip? All sugestion, comments are apreciated . . . https://reprap.org/forum/read.php?41,149114,149114#msg-149114 Mon, 05 Oct 2026 14:21:10 -0400 Phorum 5.2.23 https://reprap.org/forum/read.php?41,149114,198215#msg-198215 https://reprap.org/forum/read.php?41,149114,198215#msg-198215
msander6]]> msandersmay10 New Zealand RepRap User Group Sun, 07 Apr 2013 20:20:23 -0400 https://reprap.org/forum/read.php?41,149114,150301#msg-150301 https://reprap.org/forum/read.php?41,149114,150301#msg-150301 Alizier21 New Zealand RepRap User Group Fri, 24 Aug 2012 23:20:26 -0400 https://reprap.org/forum/read.php?41,149114,150287#msg-150287 https://reprap.org/forum/read.php?41,149114,150287#msg-150287
Arduino 0023
[github.com]
and [www.sparkfun.com]

After i copied over the files from github i had to delete the Parallel port programmers from the avrdude.conf because i was getting errors that i have no port :/
Then i hooked up the Pocket programmer to my sanguinololu board, selected the 1284p 16mhz version in arduino and hit burn bootloader using USBTinyISP.

It took about 12-15 minutes and it said verification failed, but now i can upload sketches and firmware using the arduino IDE :P]]> shippo0708 New Zealand RepRap User Group Fri, 24 Aug 2012 21:06:08 -0400 https://reprap.org/forum/read.php?41,149114,150250#msg-150250 https://reprap.org/forum/read.php?41,149114,150250#msg-150250 Alizier21 New Zealand RepRap User Group Fri, 24 Aug 2012 18:03:10 -0400 https://reprap.org/forum/read.php?41,149114,150190#msg-150190 https://reprap.org/forum/read.php?41,149114,150190#msg-150190 www.sparkfun.com]

They said its based off the USBTinyISP so I'm not sure if its incapable of writing to a 1284p like people have said is outside its memory range, but i tried it and i was able to burn a new boot loader to it :D (it verified failed but at least i could upload Marlin to it now)]]> shippo0708 New Zealand RepRap User Group Fri, 24 Aug 2012 11:24:59 -0400 https://reprap.org/forum/read.php?41,149114,150130#msg-150130 https://reprap.org/forum/read.php?41,149114,150130#msg-150130
1) windows side of things:

before you can connect your avr programmer to a mac you will need access to windows based pc ( yes....i had to install windows 7 on my mac to get the avr going) follow the pololu link on how to install the drivers and software for windows.

then i downloaded the custom firmware for mac here, and uploaded the custom firmware with terminal

if you are successfull the red LED will light up, orange LED always on..halfway there..time to boot back to mac.


2) mac side:

( arduino 0023 installed)

i updated my avr lib with avr macpack, it was 20090319 that i installed on my mac,


i played around with the azteegx1, maniacbug ,this file from github oh and i modified the avrdude.conf i was using to add the 1284p from stevesfixitshop blog. dont forget to change the fuse settings on your boards.txt (these worked for me:

Low 0xD6
High 0xDC
Ext 0xFD

burn the bootloader (avr isp v2)

board= sanguino with atmega1284p 16mhz
i used the tty.usbserial (it will show up as a dev/tty.usbserial and a dev/cu.usbserial)
then, upload the firmware.



so far i have just connected it to pronterface, i have yet to test print on it..will update as i go...]]> Alizier21 New Zealand RepRap User Group Fri, 24 Aug 2012 04:57:40 -0400 https://reprap.org/forum/read.php?41,149114,150089#msg-150089 https://reprap.org/forum/read.php?41,149114,150089#msg-150089
I'm struggling with that programmer not responding too...
I'm using a sang 1.3 board with a 1284p
I have a AVR Pocket Programmer I bought from spark fun if I need to reflag a boot loader]]> shippo0708 New Zealand RepRap User Group Fri, 24 Aug 2012 00:14:43 -0400 https://reprap.org/forum/read.php?41,149114,149918#msg-149918 https://reprap.org/forum/read.php?41,149114,149918#msg-149918 Alizier21 New Zealand RepRap User Group Thu, 23 Aug 2012 04:47:55 -0400 https://reprap.org/forum/read.php?41,149114,149170#msg-149170 https://reprap.org/forum/read.php?41,149114,149170#msg-149170 Details on the resources tab on robokits page.

Bowden looks great]]> Dust New Zealand RepRap User Group Sun, 19 Aug 2012 06:09:54 -0400 https://reprap.org/forum/read.php?41,149114,149166#msg-149166 https://reprap.org/forum/read.php?41,149114,149166#msg-149166 Alizier21 New Zealand RepRap User Group Sun, 19 Aug 2012 05:45:26 -0400 https://reprap.org/forum/read.php?41,149114,149164#msg-149164 https://reprap.org/forum/read.php?41,149114,149164#msg-149164 Alizier21 New Zealand RepRap User Group Sun, 19 Aug 2012 05:24:52 -0400 https://reprap.org/forum/read.php?41,149114,149161#msg-149161 https://reprap.org/forum/read.php?41,149114,149161#msg-149161 www.robokits.co.nz]

also I have one of these...]]> Dust New Zealand RepRap User Group Sun, 19 Aug 2012 04:58:21 -0400 https://reprap.org/forum/read.php?41,149114,149160#msg-149160 https://reprap.org/forum/read.php?41,149114,149160#msg-149160
I am trying to search for an alternative usb programmer that has the same support as the pololu . . .ive ordered some on fleabay and will have do it the way the guys at your link did . .start from scratch . .]]> Alizier21 New Zealand RepRap User Group Sun, 19 Aug 2012 04:49:18 -0400 https://reprap.org/forum/read.php?41,149114,149155#msg-149155 https://reprap.org/forum/read.php?41,149114,149155#msg-149155
[blog.think3dprint3d.com]
and
[blog.think3dprint3d.com]

they are using windows 7 and arduino version 0023 and successfully using 1284p on Sanguinololu]]> Dust New Zealand RepRap User Group Sun, 19 Aug 2012 04:24:11 -0400 https://reprap.org/forum/read.php?41,149114,149146#msg-149146 https://reprap.org/forum/read.php?41,149114,149146#msg-149146 Alizier21 New Zealand RepRap User Group Sun, 19 Aug 2012 03:24:43 -0400 https://reprap.org/forum/read.php?41,149114,149135#msg-149135 https://reprap.org/forum/read.php?41,149114,149135#msg-149135 NelsonRap New Zealand RepRap User Group Sun, 19 Aug 2012 01:06:02 -0400 https://reprap.org/forum/read.php?41,149114,149114#msg-149114 https://reprap.org/forum/read.php?41,149114,149114#msg-149114 I have been able to compile and upload firmware on sanguino with atmega 644p and with ramps 1.3 using arduino 2560 and arduino1280 boards . . .
I went on and practiced my google-fu on the subject chip and followed all the insttuctions but still cant seem to uplpad firmware on it . . .i get a programmer not responding error . .so got me thinking it might be the bootloader . .good practice though for better understanding how the arduino interface works . . .

how can i verify my installed bootloader on the chip?

All sugestion, comments are apreciated . . .]]> Alizier21 New Zealand RepRap User Group Sat, 18 Aug 2012 22:33:26 -0400