Noob requiring assistance Hi, I would like some assistance. I am currently building a CoreXY 3D printer. The board that I am using is the Duet 0.8.5. I am going to run with 2x power supply 24V but, while I am learning, I am using an old ATX 12V power supply. At the moment, I can't seem to run my stepper motors or fan with Ponterface. I am afraid that my 0.8.5 might be damaged is there a way to run a diagnostic on the Duet 0.8.5? I am unsure of what I could provide that could indicate the issues... IF I do the M115 (in the Adruino program), I get the message : "FIRMWARE_NAME:RepRapFirmware FIRMWARE_VERSION:1.09 ELECTRONICSgrinning smileyuet (+ Extension) DATE:2015-04-21" so I know it responds... I used [reprappro.com]. But I might just restart everything from the duet3d.com documentation... but the link isn't valid. Thank you for your assistance. https://reprap.org/forum/read.php?416,752142,752142#msg-752142 Mon, 09 Mar 2026 17:42:27 -0400 Phorum 5.2.23 https://reprap.org/forum/read.php?416,752142,752457#msg-752457 Re: Noob requiring assistance https://reprap.org/forum/read.php?416,752142,752457#msg-752457
Thank you all for your help.]]> Nylkos Duet Wed, 01 Mar 2017 15:20:45 -0500 https://reprap.org/forum/read.php?416,752142,752447#msg-752447 Re: Noob requiring assistance https://reprap.org/forum/read.php?416,752142,752447#msg-752447
Quote
Nylkos
Quote
dc42
I'm glad you got it working. DuwtWebControl 1.14a is the correct version to work with RRF 1.17e. M997 S1 and M997 S1 are for the Duet WiFi only.

For the Duet 0.8.5 do I require to do something to install the web control or do I just need to setup the network specs?

You just need to extract the contents of the DuetWebControl zip file to /www on the SD card, and set up the network IP address in the M552 command in config.g.]]> dc42 Duet Wed, 01 Mar 2017 14:47:41 -0500 https://reprap.org/forum/read.php?416,752142,752441#msg-752441 Re: Noob requiring assistance https://reprap.org/forum/read.php?416,752142,752441#msg-752441
Quote
dc42
I'm glad you got it working. DuwtWebControl 1.14a is the correct version to work with RRF 1.17e. M997 S1 and M997 S1 are for the Duet WiFi only.

For the Duet 0.8.5 do I require to do something to install the web control or do I just need to setup the network specs?]]> Nylkos Duet Wed, 01 Mar 2017 14:17:58 -0500 https://reprap.org/forum/read.php?416,752142,752269#msg-752269 Re: Noob requiring assistance https://reprap.org/forum/read.php?416,752142,752269#msg-752269 dc42 Duet Wed, 01 Mar 2017 03:06:24 -0500 https://reprap.org/forum/read.php?416,752142,752236#msg-752236 Re: Noob requiring assistance https://reprap.org/forum/read.php?416,752142,752236#msg-752236
Also I would require some help on how to install the Web Controler.
I copied the DuetWebControl-1.14a to the /www
I copied the files DuetWebControl-Master to the /sys

When I am trying to run M997 S2 to install it doesn't install]]> Nylkos Duet Tue, 28 Feb 2017 19:35:24 -0500 https://reprap.org/forum/read.php?416,752142,752219#msg-752219 Re: Noob requiring assistance https://reprap.org/forum/read.php?416,752142,752219#msg-752219 Here is what I have done and the result.

I upgraded (bossac) to the 1.17e.bin. the web service that I found was 1.14a.bin unsure if it's the right version...

Since I am learning I copied the 1.14a to the /sys folder and tried the M997 S2 to install the web service and I got
Quote

Invalid module number '2'
.
Have I done anything wrong? should I downgrade to 1.14a for the Bossac?

The M503 worked... the SD card responded]]> Nylkos Duet Tue, 28 Feb 2017 18:10:29 -0500 https://reprap.org/forum/read.php?416,752142,752183#msg-752183 Re: Noob requiring assistance https://reprap.org/forum/read.php?416,752142,752183#msg-752183 o_lampe Duet Tue, 28 Feb 2017 14:51:11 -0500 https://reprap.org/forum/read.php?416,752142,752161#msg-752161 Re: Noob requiring assistance https://reprap.org/forum/read.php?416,752142,752161#msg-752161 duet3d.com] and [duet3d.com]

Use [configurator.reprapfirmware.org] to setup the config.g and other needed files.

The connections on the 085 and Wifi are similar except for the network setup. The configurator web site will get the network setup properly for the board.

[reprap.org] will help on the connections.]]> stephenrc Duet Tue, 28 Feb 2017 13:35:47 -0500 https://reprap.org/forum/read.php?416,752142,752142#msg-752142 Noob requiring assistance https://reprap.org/forum/read.php?416,752142,752142#msg-752142
I am currently building a CoreXY 3D printer.

The board that I am using is the Duet 0.8.5.

I am going to run with 2x power supply 24V but, while I am learning, I am using an old ATX 12V power supply. At the moment, I can't seem to run my stepper motors or fan with Ponterface. I am afraid that my 0.8.5 might be damaged is there a way to run a diagnostic on the Duet 0.8.5?

I am unsure of what I could provide that could indicate the issues...

IF I do the M115 (in the Adruino program), I get the message : "FIRMWARE_NAME:RepRapFirmware FIRMWARE_VERSION:1.09 ELECTRONICSgrinning smileyuet (+ Extension) DATE:2015-04-21" so I know it responds...

I used [reprappro.com].

But I might just restart everything from the duet3d.com documentation... but the link isn't valid.

Thank you for your assistance.]]> Nylkos Duet Tue, 28 Feb 2017 12:08:05 -0500