; Configuration file for dc42 Kossel ; Communication and general M111 S0 ; Debug off M550 3KU_Delta ; Machine name (can be anything you like) M551 Preprap ; Machine password (used for FTP) M540 P0xBE:0xEF:0xDE:0xAD:0xFE:0x42 ; MAC Address ;*** Adjust the IP address and gateway in the following 2 lines to suit your network M552 P0.0.0.0 ; IP address (0 = use DHCP) M554 P192.168.0.254 ; Gateway M553 P255.255.255.0 ; Netmask M555 P2 ; Set output to look like Marlin M575 P1 B57600 S1 ; Set auxiliary serial port baud rate and require checksum (for PanelDue) M552 S1 ; Axis and motor configuration M569 P0 S0 ; Drive 0 goes forwards M569 P1 S0 ; Drive 1 goes forwards M569 P2 S0 ; Drive 2 goes forwards M569 P3 S0 ; Drive 3 goes backwards ; Endstops M574 X2 Y2 Z2 S1 ; Define active low and unused microswitches M665 L228.000 R108.652 H304.503 B85.0 X-0.592 Y0.165 Z0.000 ; Set delta radius, diagonal rod length, printable radius and homed height M666 X0.047 Y-0.655 Z0.608 A0.00 B0.00 ; put your endstop adjustments here, or use auto calibration to find them M208 Z0 S1 ; Set minimum Z M350 X32 Y32 Z32 E32 I1 ; Configure microstepping with interpolation M92 X160 Y160 Z160 E192 ; Set steps per mm ; Motor current, speed and acceleration M906 X900 Y900 Z900 E1700 I30 ; Set motor currents (mA) M201 X800 Y800 Z800 E1000 ; Set accelerations (mm/s^2) M203 X18000 Y18000 Z18000 E12000 ; Set maximum speeds (mm/min) M566 X500 Y500 Z500 E1000 ; Set maximum instantaneous speed changes (mm/min) G21 ; Work in millimetres G90 ; Send absolute coordinates... M83 ; ...but relative extruder moves ; Thermistors and heaters M301 H0 S1.00 P10 I0.1 D200 T0.4 W180 B30 ; Use PID on bed heater (may require further tuning) M305 P0 T100000 B3960 C0 R4700 ; Set thermistor + ADC parameters for heater 0 M143 H0 S120 ; Set temperature limit for heater 0 to 120C M305 P1 T100000 B4138 R4700 H0 L0; Set thermistor + ADC parameters for heater 1 M307 H1 A183.1, C149.0, D7.1 S0.5 ; PID settings for extruder 0 M570 S200 ; Allow extra heating time ; Tool definitions M563 P0 D0 H1 ; Define tool 0 G10 P0 S0 R0 ; Set tool 0 operating and standby temperatures ; Z probe and compensation definition M558 P5 X0 Y0 Z0 I1 H2 F100 T3000 ; Set Z probe type to switch, the axes for which it is used and the probe + travel speeds M557 R85 S20 ; Define mesh grid G31 P950 X0 Y0 Z3 ; Set Z probe trigger value, offset and trigger height ; Custom settings are not configured M307 H3 A-1 C-1 D-1 ; reserve pin H3 for M42 command ;*** If you are using axis compensation, put the figures in the following command M556 S78 X0 Y0 Z0 ; Axis compensation here M207 S7.0 F3600 Z0.1 ; Set firmware retraction details M572 D0 S0.1 ; set pressure advance T0 ; select first print head