Subject		Views	Posts	Last Post
	Questions with Dual Extrusion - E3D Cyclops / Diamond Hotend experience question by PDBeal	176	2	11/21/2018 02:27PM Last Post by dc42
	TMC2130 sensorless homing; forces? by HugoW	555	8	11/20/2018 07:38AM Last Post by MKSA
	Use the full graphic controller without a printer by PickyBiker	2,181	29	11/19/2018 11:00AM Last Post by SupraGuy
	Best Auto level sensor & Extruder?   (Pages: 1 2) by Ed3D	1,028	47	11/18/2018 03:59PM Last Post by MechaBits
	Ein Hilferuf and die 3D Druck Community by Gründerwoche Team	493	3	11/17/2018 01:36AM Last Post by o_lampe
	Automatic Zoom 3MP CCTV IR Lens by sz3bbylA	112	1	11/16/2018 04:25PM Last Post by sz3bbylA
	Display 12864 didn't working MKS GEN V1.4 by tumulo97	912	4	11/13/2018 05:54PM Last Post by velvetbrain
	no hotend forum and e3d v6 and clones question by terramir	389	7	11/13/2018 01:10PM Last Post by reifsnyderb
	Planning on upgrading control board on Cetus...Einsy Rambo good choice? by guycobb2	266	18	11/12/2018 08:13AM Last Post by dc42
	PID tuning while printing by kullboys	587	3	11/11/2018 11:23PM Last Post by o_lampe
	An Automatic Infinite 3D Printer by mso797	494	6	11/10/2018 05:58PM Last Post by xdarko
	Ender 3 Y axis problem by AlexPl	1,122	3	11/08/2018 12:19PM Last Post by pliers
	Raised letters by skaha	340	2	11/07/2018 06:58PM Last Post by skaha
	scaling by skaha	542	6	11/06/2018 03:01PM Last Post by skaha
	No Z moves in Prusa Edition of Slic3r ( Classic Slic3r works fine) by PARADOXICLES	411	7	11/04/2018 08:58PM Last Post by PARADOXICLES
	Marlin new firmware 1.1.9 by yar60	1,548	16	11/04/2018 12:36PM Last Post by chiques
	How to fix RAMPS 1.4 X Axis end stop short circuit? by dublo7	125	4	11/04/2018 09:10AM Last Post by Roberts_Clif
	Geeetech A10 / higher temperatures by RepMike	146	8	11/04/2018 09:02AM Last Post by Roberts_Clif
	Edit by Holy1	383	3	11/03/2018 09:52PM Last Post by Holy1
	Feed rate calculation for 3D printing by jakijain	827	5	11/03/2018 10:23AM Last Post by Roberts_Clif
	Want an heated Chamber? Zatsit's ultra simple solution by M_Xeno	980	7	10/26/2018 08:30AM Last Post by sliceheart
	New E3D V6 (From China) Clogs as soon as PLA Enters   (Pages: 1 2) by InspecteurSpie	9,398	46	10/25/2018 04:53PM Last Post by frankvdh
	Introduction (new member) by petersmall	783	4	10/25/2018 02:21AM Last Post by jefbed
	fast stepper motor by charlieRC	407	22	10/24/2018 06:42PM Last Post by VDX
	Rescaling multi objects at once by kevin_kss	287	4	10/24/2018 08:57AM Last Post by kevin_kss
	Funny question about priming by Tinchus	572	10	10/23/2018 11:22PM Last Post by Ezrec
	Cercasi Esperto in trafilatura per stampa 3d by ENRICO FRASSINETTI	715	2	10/23/2018 10:50AM Last Post by ENRICO FRASSINETTI
	An open source kiln as part fo the RepRap project? by John Cummings	784	21	10/22/2018 02:50PM Last Post by MKSA
	Reprap discount full graphic smart controller not working by ikaarus	20,295	21	10/22/2018 02:48PM Last Post by frenndds
	support material by Thorp	6,254	25	10/22/2018 12:36PM Last Post by ottensmeyer