Welcome! Log In Create A New Profile

Advanced

RepRap Host

Java - everyone loves it and it works well everywhere. Maybe. 
Subject Views Posts Last Post

How to output Gerber files from gEDA so RepRap Host Software can read them

by Azzan
1,251 1 03/01/2012 02:28AM
Last Post by Azzan

Pronterface set position as home?

by shippo0708
4,764 4 02/27/2012 06:40AM
Last Post by DeuxVis

Joystick

by toehead
1,555 2 02/13/2012 03:31AM
Last Post by VDX

New Pronterface

by librav
2,009 5 02/09/2012 05:48AM
Last Post by rhmorrison

Installing from source: Wiki instructions are vague

by jbayless
1,032 2 02/09/2012 01:58AM
Last Post by jbayless

Stuck when feeding plastic!!

by kmoust
1,144 2 01/18/2012 04:01AM
Last Post by DeuxVis

Pronterface pause/resume to reload filament

by Zarquon
3,547 2 01/08/2012 06:54AM
Last Post by bobc

Pronterface minimum system requirements ?

by 3D2B
2,059 2 01/07/2012 06:44PM
Last Post by Auzze

Propeller Plug

by Grogyan
3,466 11 12/20/2011 02:01AM
Last Post by CP

Need Printing Advice Attachments

by librav
1,460 6 12/19/2011 03:48AM
Last Post by nophead

Where are the Gcode Circle Commands?

by isometrik
2,590 4 12/09/2011 07:21AM
Last Post by DeuxVis

Skeinforge contributions

by Enrique
17,185 29 12/08/2011 07:19PM
Last Post by Jacob

Software does not start

by ThijsRoumen
1,555 4 11/24/2011 07:53AM
Last Post by DeuxVis

Pronterface- Center part on print bed?

by roygpa
5,337 3 11/14/2011 02:35AM
Last Post by rhmorrison

Reprap host hangs

by zapman
1,570 3 10/24/2011 05:14AM
Last Post by zapman

Software Project

by Kortal
1,074 2 10/22/2011 11:57AM
Last Post by zapman

plotter Attachments

by shane-paul
1,380 1 10/10/2011 11:11AM
Last Post by shane-paul

On start Reprap shows text and GUI never opens

by Joe 'Volg' Greene
2,259 6 10/07/2011 07:58PM
Last Post by Sean Tasker

RepRapHost does not combine TeMpOrArY files

by aref_naa
1,267 4 09/25/2011 04:06AM
Last Post by danx3

ATMega328 firmware

by mccoyn
5,903 17 09/15/2011 11:43AM
Last Post by shippo0708

Installing in 64 bit Ubuntu

by Anonymous User
11,222 24 09/07/2011 09:37AM
Last Post by Cyberwizzard

RepRap host with gen 6 board ...

by alwarrior
1,256 2 09/05/2011 03:56AM
Last Post by Alain

Need help for Host installation hot smiley Attachments

by Tarz
1,372 5 08/24/2011 04:35AM
Last Post by brett sutton

Nozzle crushes print at end of every run

by danieljabailey
1,514 8 08/23/2011 11:22PM
Last Post by cyborg527

Arduino with Gen 6 board

by Javaid Butt
1,080 2 08/23/2011 03:25PM
Last Post by Javaid Butt

reprap host software

by chlluk
1,683 1 08/09/2011 04:33AM
Last Post by chlluk

Problems running RepRap Host.

by alfalover
1,814 4 07/28/2011 05:42PM
Last Post by Aircatcher

New, improved G-code firmware for RepRap (and other applications) Attachments

by Anonymous User
17,492 28 07/25/2011 02:34PM
Last Post by isidoro

Holes in top layer

by danieljabailey
2,720 6 07/19/2011 01:46PM
Last Post by nophead

I don't see the 'plan view'

by EddieG
1,655 4 07/11/2011 02:10AM
Last Post by rhmorrison