Welcome! Log In Create A New Profile

RepRap en Español

Page 1 of 29 Pages: 12 3 4 5

Forum List New Topic RSS

	Views	Posts	Last Post
Iniciar el LCD Discount Smart Controller en el Marlin by Noqui	196	1	02/13/2024 04:05AM Last Post by Noqui
Problemas eje Y prusa Steel by Nest	2,142	1	04/02/2022 04:14AM Last Post by Nest
stringing en prusa p3steel pro v.2 by bobazza	2,069	2	03/31/2022 01:35PM Last Post by Valvulin
cama prusa p3steel pro v.2 by bobazza	2,091	2	03/31/2022 01:30PM Last Post by Valvulin
Error al hacer homing by NavaRo	2,704	1	10/01/2021 11:38AM Last Post by NavaRo
Mi impresora se detiene de repente by NavaRo	2,886	1	09/14/2021 02:45PM Last Post by NavaRo
Novato con fallo en codigo by kenshin3527	3,381	1	05/07/2021 04:37PM Last Post by kenshin3527
Programa para hacer girar piezas 3d y crear videos by omarlopez	5,083	5	04/09/2021 03:20AM Last Post by zhangzetian
Cómo se podría construir una impresora de comida 3d? by erjavi_zgz	4,201	2	12/10/2020 08:17AM Last Post by Roberts_Clif
Impresora con RAMPS by esnoan	4,506	1	06/25/2020 11:56PM Last Post by esnoan
EJE Z NO FUNCIONA CORRECTAMENTE by lewuh15	5,678	3	06/21/2020 12:51PM Last Post by esnoan
Error en Repetier, al convertir a G.code by Jaume Cat	4,600	2	05/04/2020 07:44AM Last Post by Jaume Cat
Problemas con mi Ramps by NavaRo	4,644	2	04/14/2020 09:15PM Last Post by qubotica
problema con la cama caliente, sube sola de temperatura by yuis	11,858	10	02/15/2020 07:19PM Last Post by alldigitall
Alisado de capas consulta sobre si el eje z puede ser negativo. by apamaster	5,486	2	02/14/2020 04:14PM Last Post by Lepes
Prusa parada varios meses by Jaume Cat	6,307	7	02/14/2020 04:05PM Last Post by Lepes
Buscando gente en Valencia by EgonVLC	4,920	1	02/04/2020 07:08AM Last Post by EgonVLC
Problema ramps by Ramiro14	6,128	8	11/14/2019 07:02AM Last Post by Lepes
Baja de temperatura al activar fan de capas by mbr386	6,109	2	11/14/2019 07:00AM Last Post by Lepes
problema con hotend y hotbed by fernandotournier	6,456	4	10/08/2019 02:18AM Last Post by JesterRace
Extrusor no calienta by derpax1	5,669	1	10/02/2019 06:19PM Last Post by derpax1
Problema de la cama (eje z) by juansesilvestrini	5,378	1	09/04/2019 08:38AM Last Post by juansesilvestrini
Impresora 3D Flusun i3 C, No funciona by JaimePala	5,608	3	07/16/2019 01:18PM Last Post by JaimePala
Eje no funciona by vitu	5,597	2	05/03/2019 06:05PM Last Post by qubotica
Problemas de impresión - Prusa I2 by qubotica	5,764	1	05/03/2019 06:01PM Last Post by qubotica
Ventilador de capa siempre encendido by jcnet	9,710	4	03/24/2019 05:11PM Last Post by Valvulin
Problema ramps+arduino by picopop	5,478	2	03/24/2019 05:06PM Last Post by Valvulin
Cama Caliente 16cm de diametro para 30cm by sarindangui	5,363	2	03/24/2019 04:54PM Last Post by Valvulin
Proyecto para 0,05 mm de altura de capa by Peirof	5,578	1	01/25/2019 01:00AM Last Post by Peirof
nueva impresora 1000x1000x1000mm by frany	5,708	1	12/23/2018 04:50AM Last Post by frany

Page 1 of 29 Pages: 12 3 4 5