Welcome! Log In Create A New Profile

Australia, Melbourne RUG

Page 3 of 6 Pages:

Forum List New Topic RSS

	Views	Posts	Last Post
3.0mm Ø ABS Extrudate Manufacturer - Melbourne by SNOMANN	2,668	21	08/24/2012 10:56PM Last Post by Vijay Atawane
MendelMax - Yes? No? Your experiences? by Jon	839	2	08/23/2012 10:21PM Last Post by Cefiar
A box of some sort of plastic pellets - free to good home by gazob	944	3	08/16/2012 05:27AM Last Post by gazob
First Steps by AJT	785	2	08/09/2012 07:28PM Last Post by Cefiar
$5 off each roll, plus free express shipping on 3mmABS by wilsonj	1,024	3	08/07/2012 04:00AM Last Post by wilsonj
We supply PLA,ABS filaments by Anonymous User	3,329	23	08/06/2012 06:37PM Last Post by Cefiar
RAMPS Electronics by lost	1,522	7	06/26/2012 01:52AM Last Post by ted
Next Melbourne Meetup by Dragonbane	1,736	21	06/15/2012 08:42PM Last Post by bmsweb
Kwando checking in by kwando	1,195	10	06/04/2012 08:39PM Last Post by Auzze
[EOI] Sanguinololu v1.3a boards by HaniC	1,019	2	05/24/2012 01:24AM Last Post by bmsweb
Newbie from melb... by HaniC	841	2	05/20/2012 08:47PM Last Post by Cefiar
Prusa Air v2 by tas_tig3r	1,221	1	05/17/2012 08:29PM Last Post by tas_tig3r
nooby hi all by mattyyy	873	2	05/16/2012 11:33PM Last Post by Cefiar
Prusa finished! by pinchies	1,229	1	05/05/2012 10:22PM Last Post by pinchies
Printrboard - Anyone using these or know much about them? by bmsweb	2,463	13	04/26/2012 03:43PM Last Post by bmsweb
Configuring Sprinter by jman	1,258	4	04/15/2012 08:21AM Last Post by jman
Heatsinks for Stepstick by pinchies	890	2	04/15/2012 12:38AM Last Post by Auzze
Are there any RepRappers from Bendigo in here? by Corin	1,118	8	04/13/2012 02:56AM Last Post by ChrisM
Problems that popped up building a Prusa by sgall	1,059	2	04/01/2012 06:24PM Last Post by Auzze
Newbie problems during a Prusa build by sgall	1,243	1	04/01/2012 05:51AM Last Post by sgall
Starting on a repstrap by tjkerr	1,261	12	03/28/2012 03:31AM Last Post by IceMan
Here is where I source my RepRap Mendel Parts by Magician	2,117	5	03/20/2012 06:19PM Last Post by bobbintb
Reprap Complete and first parts a success by Magician	1,005	4	03/08/2012 05:31PM Last Post by ZombieBait
Prusa Iteration 2 by jman	1,110	4	03/04/2012 05:39PM Last Post by jman
Local Hot end suppliers? by pinchies	1,141	2	02/29/2012 10:36AM Last Post by scwerta
Proposal - The Part Per Month Project by Shibboleth	1,173	4	02/29/2012 06:53AM Last Post by plim
Prusa Mendel printed parts by Jasper	1,423	6	02/29/2012 03:21AM Last Post by Gibbedy
Successful install of Budaschnozzle 1.1 Hot End on Greg's Lm8uu X Carriage by Magician	1,307	1	02/25/2012 12:47AM Last Post by Magician
Bearing and Rod lubrication by bmsweb	1,470	6	02/17/2012 09:16AM Last Post by IceMan
Disposing of hazardous chemicals by Myndale	861	1	02/15/2012 09:32PM Last Post by Myndale

Page 3 of 6 Pages:

1 234 5