Welcome! Log In Create A New Profile

Advanced

Controllers

Anything related to printer controllers not being Duet, RAMPS or Sanguinololu: microprocessors, motor and heater driver circuitry, gEDA/KiCAD issues, soldering tips, etc. 
Page 2 of 81    Pages: Previous12345NextLast
Forum List New Topic RSS
Subject Views Posts Last Post

MAXTEMP BED...please reset.

by DanL 		194 5 04/04/2019 10:17PM
Last Post by DanL

Re-ARM from Panucatt   (Pages: 1 2 3 4)

by .Jata 		10,092 100 04/04/2019 02:04PM
Last Post by MMcLure

is TB6560 can drive this motor?

by okuzster 		173 6 04/04/2019 10:59AM
Last Post by okuzster

LJ12A3-2-Z/BX onto RADDS 1.6 Board?

by unf0rg0tt3n 		322 13 04/01/2019 02:01AM
Last Post by unf0rg0tt3n

Galvo Laser Control Firmware

by marinusdebeer 		1,140 12 03/29/2019 07:24PM
Last Post by VDX

Tiny Filament Sensor - Optical Version Attachments

by fredchan 		198 3 03/28/2019 03:15AM
Last Post by fredchan

Channel usage on Controller

by Inq 		163 5 03/26/2019 08:40AM
Last Post by Inq

None existent chinese Q.C Attachments

by Pippy 		277 9 03/25/2019 12:51AM
Last Post by PhatFil

MKS BASE Attachments

by Roberts_Clif 		243 2 03/22/2019 12:03PM
Last Post by Roberts_Clif

Calling all Rumba experts Attachments

by Modmike 		850 22 03/14/2019 04:04PM
Last Post by Tomaslund

Logic-level bed FET connected to RADDS pin - default to "on" when firmware not booted?

by Timpanogos Slim 		192 4 03/13/2019 03:20AM
Last Post by dc42

Lerdge X with dual Z

by mga 		249 1 03/08/2019 10:51AM
Last Post by mga

Problem with MKS Robin 2.4

by NBonev 		233 1 03/07/2019 02:36PM
Last Post by NBonev

MKS GEN v1.4 Schematic

by Pippy 		338 4 03/05/2019 05:27AM
Last Post by Pippy

Noise on temperatur sensors - MKS Gen 1.4 Attachments

by flydeprutten 		1,344 10 03/03/2019 07:18AM
Last Post by Pippy

Confused regarding RUMBA pinout

by chrstrvs 		256 3 03/03/2019 06:16AM
Last Post by chrstrvs

TMC 2208 modes

by Shreks donkey 		1,792 10 02/27/2019 07:17PM
Last Post by Shreks donkey

Newbie question - firmware backup

by rklauco 		2,044 5 02/27/2019 06:09PM
Last Post by Richard_Brown

MKS Gen L + TFT 28 Display menus missing

by Manolocs 		612 8 02/25/2019 08:07AM
Last Post by MKSA

STM32F1/F4 3d Printer board for Marlin Attachments   (Pages: 1 2)

by victor_pv 		8,333 51 02/18/2019 07:06AM
Last Post by Pippy

how to upload firmware to melzi v2 board? Attachments

by kkwong1951 		8,026 17 02/15/2019 10:11PM
Last Post by Richard_Brown

TMC 2208 on ramps plugged straight in no mods marlin advice

by Paul41 		452 3 02/15/2019 09:23AM
Last Post by Gecko23

Help diagnosing issue with MKS Gen L board with CR10

by Paul41 		1,045 8 02/15/2019 09:14AM
Last Post by Gecko23

GT2560... How many mA can I request on ADC

by zonalimitatore 		222 12 02/15/2019 05:07AM
Last Post by zonalimitatore

RADDS work now stable with RepRap Firmware   (Pages: 1 ... 26 27 28)

by angelo 		40,535 815 02/14/2019 05:44PM
Last Post by VDX

Problem connecting board mks gen l

by Lc1975 		1,012 11 02/13/2019 05:02AM
Last Post by Lc1975

Double V ref from stepper drivers

by Shreks donkey 		295 4 02/12/2019 05:02PM
Last Post by Shreks donkey

Using onboard stepper motor drivers with MKS SBase 1.3?

by papergeek 		407 3 02/04/2019 05:05PM
Last Post by papergeek

Thermistors giving higher temperature than expected

by shimonchick 		186 2 02/01/2019 12:20PM
Last Post by VincentM

Fried MKS Gen L board?

by Shreks donkey 		615 8 01/26/2019 06:42PM
Last Post by Shreks donkey
Page 2 of 81    Pages: Previous12345NextLast