Welcome! Log In Create A New Profile

Controllers

Anything related to printer controllers not being Duet, RAMPS or Sanguinololu: microprocessors, motor and heater driver circuitry, gEDA/KiCAD issues, soldering tips, etc.

Page 35 of 85 Pages:

33 343536 37

Forum List New Topic RSS

	Views	Posts	Last Post
auto bed leveling problem by ottist	1,556	3	05/05/2014 08:33AM Last Post by ottist
[Rumba + FGS-LCD-C] USB connection and flashing problem by Couby	2,322	4	05/04/2014 06:33AM Last Post by Couby
wanhao duplicator 3 - new controller by kiam	591	1	05/02/2014 05:21AM Last Post by kiam
Getting started with electronics (Gen7?) by Rudbot	873	12	05/01/2014 07:14AM Last Post by Traumflug
100k resistor on MS1 pin of A4988 Carrier by FBITuco	1,978	5	04/30/2014 09:38AM Last Post by FBITuco
LCD Display for RUMBA Board by Xhnnas	739	1	04/28/2014 04:42AM Last Post by Xhnnas
Xmega based design? by kscharf	1,563	7	04/26/2014 02:07AM Last Post by mattairtech
Azteeg X3 Pro Digipin by TheAbstractVoid	583	1	04/22/2014 06:53AM Last Post by TheAbstractVoid
electronics suggestions or limitations by Natas70	884	10	04/21/2014 09:38PM Last Post by Natas70
Azteeg X3 - connection to power supply by bishupz1	695	1	04/21/2014 04:33PM Last Post by bishupz1
Externally powering mk2a heatbed by darkestelephant	377	2	04/20/2014 07:13PM Last Post by waitaki
Powering a 12v LED bulb above printer, from a 12v supply? by RickM	905	4	04/19/2014 07:07AM Last Post by Learner
Troubleshooting Optical endstops by Ohmarinus	993	4	04/18/2014 10:53AM Last Post by Ohmarinus
T-Bone: A radically new Reprap Board by InteractiveMatter	2,419	30	04/17/2014 11:36AM Last Post by Ohmarinus
[SOLVED] How do I calculate the reference voltage for Melzi board stepper drivers? by tobben	4,923	8	04/15/2014 01:46PM Last Post by NoobMan
SERVO work with SaintSmart but not with ARDUINO by Playback	686	1	04/14/2014 08:09PM Last Post by Playback
RUMBA random disconnects by Rigor_M	833	3	04/14/2014 07:04PM Last Post by Rigor_M
Rambo 1.2x board by sbloom67	986	4	04/11/2014 08:30AM Last Post by tjb1
RUMBA Debug by twicx	471	3	04/11/2014 08:28AM Last Post by tjb1
reprap.me stepsticks and Gen7 ? by mcp	1,508	11	04/10/2014 08:56AM Last Post by Ironaxe
Help! Static electricity buildup keeps killing my prints! by CmdrKeen	1,215	4	04/07/2014 09:56AM Last Post by majic79
Power supply shuts down when heated bed MK2a is connected. by ghobbs	1,219	12	04/06/2014 05:01PM Last Post by ghobbs
RambO Mosfets by phinsil6	534	4	04/05/2014 08:00PM Last Post by phinsil6
Heated bed power calculation by zipmsp	2,939	3	04/02/2014 10:16PM Last Post by zipmsp
If my electronics are all PSU powered but they turn on my PSU, how do I turn my printer on? by SamS	479	5	04/01/2014 11:07PM Last Post by milt
Heated bed..... More like luke warm bed.... Help? by cfy7	739	2	04/01/2014 06:31AM Last Post by Dust
Axis Calibration by Paul Armin	392	4	03/31/2014 05:47AM Last Post by NoobMan
motors not turning just vibrating by sdp1107	439	2	03/31/2014 05:39AM Last Post by Traumflug
Should the I/O pins be current protected? by cgosnell	502	2	03/27/2014 01:19PM Last Post by NoobMan
160mm diameter round PCB HBP? by Dust	1,147	3	03/27/2014 12:22PM Last Post by Genie

Page 35 of 85 Pages:

33 343536 37