Welcome! Log In Create A New Profile

Advanced

Controllers

Anything related to printer controllers not being Duet, RAMPS or Sanguinololu: microprocessors, motor and heater driver circuitry, gEDA/KiCAD issues, soldering tips, etc. 
Subject Views Posts Last Post

Calibrating different stepper drivers

by JoeDaStudd
776 5 03/27/2014 11:30AM
Last Post by NoobMan

Firmware not working on delta-pi with RAMPS 1.4 and mega 2560

by Thijs
1,020 4 03/26/2014 05:25PM
Last Post by Thijs

Power supply input

by Dom22
455 6 03/26/2014 11:46AM
Last Post by mkelly

Melzi current draw?

by PeteD
721 1 03/25/2014 12:37PM
Last Post by PeteD

Advise on thermocouple

by Rigor_M
541 6 03/24/2014 04:18PM
Last Post by NoobMan

LCD-TFT Screen Ultimaker 2?

by TRoager
1,373 5 03/24/2014 02:54AM
Last Post by TRoager

Megatronics v2 problems

by prusanoob
3,083 13 03/21/2014 08:29PM
Last Post by vreihen

Where are the Azteeg X3 v1.2 gerber files?

by deluz
1,120 13 03/21/2014 07:45PM
Last Post by NoobMan

Duet questions

by ketil
824 4 03/21/2014 12:17PM
Last Post by T3P3

compare 8 bit to 32 bit printer controller

by zaius
9,835 7 03/21/2014 10:33AM
Last Post by angelo

Anyone built a cooldrv stepper driver?

by JNOD
1,147 8 03/19/2014 07:37AM
Last Post by GowthamJGR

Unusual stepper ratings - vref settings for new Melzi   (Pages: 1 2 3)

by Mr Joshua
3,773 74 03/18/2014 07:54PM
Last Post by Mr Joshua

Need some help for the cables. Attachments

by BoByS
609 3 03/18/2014 09:39AM
Last Post by BoByS

DIY Power Supply?

by zipmsp
2,854 10 03/17/2014 06:59PM
Last Post by zipmsp

Ramps 1.4 to pins.h: need help!

by Janski
978 5 03/14/2014 10:21AM
Last Post by tjb1

Ramps 1.4 Board Question: Shortcircuit - Help PLz! Attachments

by Janski
657 3 03/13/2014 07:58PM
Last Post by Janski

Steppers not have enough juice?

by tyscof
446 5 03/12/2014 11:43PM
Last Post by Mattasmack

Linear Bipolar Stepper Driver... Looking for input on development

by MacSkyver
836 1 03/11/2014 07:19PM
Last Post by MacSkyver

First Motherboard

by 87morpheus
1,549 19 03/09/2014 05:14AM
Last Post by ndujar

Gen7 v1.3.1 Atmega644 Electronics Bootloader Upload

by gphysics2014
739 1 03/08/2014 08:18PM
Last Post by gphysics2014

Azteeg X3

by Johnnymoto
384 2 03/07/2014 04:23AM
Last Post by Johnnymoto

Azteeg is not working properly with motors

by NeoTheFox
377 2 03/06/2014 12:14PM
Last Post by JeanYamb

Hilfe Slave defekt automatisch Master kaput

by weigi
370 2 03/03/2014 04:39PM
Last Post by VDX

What would cause controller to reset back to defaults?

by trsills
591 3 03/03/2014 02:52PM
Last Post by Creo

Anyone own a working Panelolu2 for Sanguinololu who can help?

by JNOD
716 5 03/03/2014 02:35PM
Last Post by T3P3

Rambo board and motors

by Ryusei
497 5 03/01/2014 04:55AM
Last Post by Ryusei

Dual extrusion TB6560 controller Attachments

by vajpeters
4,139 29 02/28/2014 05:51PM
Last Post by vajpeters

Megatronics 2.0 -> Connect servo for z-axis probing

by lutjanus
2,019 3 02/28/2014 04:19PM
Last Post by lutjanus

Signs of a failing Thermistor?

by Ohmarinus
12,016 13 02/28/2014 05:09AM
Last Post by suramu

USB (flash drive) reader instead of SD Card

by Kryptonit3
2,456 4 02/27/2014 11:33AM
Last Post by Kryptonit3