Welcome! Log In Create A New Profile

Advanced

Controllers

Anything related to printer controllers not being Duet, RAMPS or Sanguinololu: microprocessors, motor and heater driver circuitry, gEDA/KiCAD issues, soldering tips, etc. 
Subject Views Posts Last Post

Homing the Z Axis causes a hard reset

by TDecker
691 5 12/16/2017 01:54PM
Last Post by TDecker

MKS BASE 1.4 Dead MOSFET and solutions Attachments

by Min1291
816 2 12/15/2017 08:07PM
Last Post by Roberts_Clif

MKS base 1.2 and auto bed leveling

by laazarus
6,995 13 12/12/2017 02:44AM
Last Post by legozebra

Problem flashing Marlin onto Melzi board.

by Anonymous User
922 1 12/02/2017 06:15PM
Last Post by Anonymous User

Possibility of replacing Andciv board for another Attachments

by Xaimill
546 3 11/26/2017 09:13PM
Last Post by edvard rahel

Reprap Firmware on Due/RADDS SD Card

by mrwizzard
1,103 6 11/20/2017 04:28PM
Last Post by mrwizzard

MKS Gen v1.4 Steppers not turning.

by usajet
511 1 11/13/2017 01:43PM
Last Post by usajet

Repairing a Printrboard potentiometer

by hussainsail2002
659 3 11/07/2017 10:36AM
Last Post by o_lampe

MKS Gen 1.4

by JustSumGuy
769 2 11/06/2017 04:05PM
Last Post by JustSumGuy

Controller board with Extruder & 4-axis control.

by jason1989
787 4 11/02/2017 03:48AM
Last Post by dc42

Choosing the right MOSFET

by obelisk79
760 8 10/31/2017 07:32AM
Last Post by obelisk79

Questions on driving DC motors with Arduino using PWM

by GeertB
10,119 15 10/26/2017 04:57PM
Last Post by dc42

Controller board for up to 5 exrtuders

by deaconfrost
579 1 10/23/2017 10:41AM
Last Post by deaconfrost

MOSFET to MOSFET

by mikes3ds
571 3 10/17/2017 11:22AM
Last Post by edvard rahel

MKS SBASE V1.3, what end stop connectors?

by HugoW
769 1 10/15/2017 01:41PM
Last Post by HugoW

Melzi with latest Arduino IDE?

by spechter
2,877 4 10/12/2017 01:45PM
Last Post by TobiasWilp

New 32bits board based on STM32F4

by xebbmw
3,266 13 10/11/2017 03:21PM
Last Post by kryozxcrew

Overclock/reclock atmega 2560?

by DjDemonD
3,646 12 10/10/2017 09:30PM
Last Post by Dust

MKS Robin + SSR

by konstantinos2424
1,165 7 09/21/2017 07:59AM
Last Post by konstantinos2424

MKS BASE - procedure to diagnose / swap bad mosfet

by david784
1,297 4 09/11/2017 04:21PM
Last Post by david784

Selecting the right electronics for my project

by yala
747 17 09/06/2017 02:51AM
Last Post by dc42

RUMBA board or Smart Controller LCD 'idiosyncrasy?"

by TJM3D
615 4 09/04/2017 03:47AM
Last Post by o_lampe

Prusa extruder mux

by Dust
803 3 08/22/2017 12:10PM
Last Post by dc42

Dumb question about RADDS hall sensor

by bryanbdp
403 2 08/21/2017 03:14AM
Last Post by o_lampe

How to set up microstep on StepStick using A4988 ?

by trietdao95
600 3 08/16/2017 08:15PM
Last Post by Dust

tronxy melzi 2 boards??

by munchit1
1,816 5 08/15/2017 10:21AM
Last Post by munchit1

What's the easiest way to do this?

by Desertboy
423 2 08/15/2017 03:58AM
Last Post by o_lampe

The probably cheapest and most modular 32bit solution.

by JustAnotherOne
993 7 08/12/2017 03:00PM
Last Post by JustAnotherOne

Sinaptec DIY build Attachments

by Dominium
982 3 08/05/2017 04:35AM
Last Post by Dominium

Megatronics V2- Inverted end stop damage IC2 Attachments

by MRGiacalone2005
1,323 11 08/01/2017 11:20PM
Last Post by Dust